Category: A-B

About the 1746-NT8

The 1746-NT8 is Allen-Bradley’s SLC 500 thermocouple/voltage analog input module.

It is a chassis-mounted, eight (8) channel module that receives thermocouple/voltage signals and converts them to digital signals for retrieval by any SLC 500 processor.

It has a backplane current rating of 120mA at 5V DC and 70mA at 24V DC for a total backplane power of 2.28W.

The 1746-NT8 uses a delta-sigma signal conversion method and has a digital low-pass filter with selectable programmable filter frequencies.

The normal mode rejection between terminals is greater than 100 dB at 50-60 Hz, and the common mode rejection between input and ground is greater than 100 dB at 50-60 Hz.

The 1746-NT8 module automatically calibrates itself approximately every 2 minutes after power-up.

It provides +/-30V DC and 600W pulses for 1ms input overvoltage protection and 12.5V DC circuit isolation between inputs and chassis ground, and between inputs and backplane, with a test voltage of 500V DC for 1 minute.

The 1746-NT8 has nine green LEDs to indicate channel status and module status.

It uses the 1746-RT34 (RTB) removable terminal block to connect the input devices. The terminal block includes two (2) cold junction compensation (CJC) sensors with an accuracy of +/-1.72 degrees Celsius.

The 1746-NT8 has several selectable input types with a total input impedance greater than 10 M ohms.

Any input device connected to it must have an impedance of less than 100 ohms to meet accuracy requirements.

The 1746-NT8 offers optional open-circuit detection at 1 cycle per channel for an overall input dry-circuit response time of 400 milliseconds.

The functional temperature range of the module is 0 degrees Celsius to 60 degrees Celsius. The functional temperature range of the module is 0 degrees Celsius to 60 degrees Celsius.

The modules are UL and CUL recognized.

1746-NT8 is an analog input module belonging to the SLC 500 product family.

The module is specifically dcs-sis.com designed for thermocouple/millivolt inputs and is compatible with SLC 500 processors such as SLC 5/01. 5/02. 5/03. 5/04. and 5/05. It can be used with SLC fixed or modular hardware categories.

Similar to other analog input modules, the 1746-NT8 uses Sigma-Delta modulation to convert received analog signals to digital values.

The converted data is stored in the module’s local memory and transferred to the CPU to create a data table to store the digitally converted values.

The module can be mounted in a fixed chassis, specifically using the 1746-A2 chassis.

If used with a modular controller, the module can be installed in any slot except slot 0.

Slot 0 is always reserved for controllers or communication adapters such as Remote IO, Data Highway Plus (DH+), and Ethernet communication modules.

Description:

The 1783-MX08T switch is an Allen-Bradley managed Ethernet switch.

About the 1783-MX08T

The 1783-MX08T Switch, manufactured by Allen-Bradley, is a Stratix 8000 modular managed Ethernet switch.

The managed switch has up to eight ports and is powered from 24 to 48 V DC.

The 1783-MX08T switch provides an optimized solution for both IT and manufacturing environments.

The Allen-Bradley Stratix 8000 Managed Modular Switch is jointly manufactured by Rockwell Automation and Cisco.

The 1783-MX08T switch features a user-friendly interface that ensures users have an easy installation process and a simple control environment.

In addition, the 1783-MX08T switch supports the RXLogix 5000 operating environment as well as diagnostic panels to further simplify use.

The 1783-MX08T switch is designed to provide simple and secure integration with the corporate network.

 This is accomplished through the CIP interface, which allows integration with enterprise-connected devices.

The Allen-Bradley 1783-MX08T switch measures 112 mm in length, 97 mm in width, and 147 mm in height.

The recommended ambient operating temperature range is -40 to 60 degrees Celsius. 

The ambient storage temperature range is -40 to 85 degrees Celsius and the relative humidity is rated at 5% to 95% non-condensing.

The 1783-MX08T switch has an open housing and supports an inrush current rating of 2 amps.

The unit utilizes a 10/100 Base T Cooper Ethernet port. The supported memory type is CompactFlash memory.

DESCRIPTION

The 1783-MX08F Switch is an Allen-Bradley network switch. The module is an 8-port switch with 100 Base-F fiber optic Ethernet ports.

About the 1783-MX08F

The 1783-MX08F Switch, manufactured by Allen-Bradley, is an 8-port Stratix 8000 switch.

The 1783-MX08F switch has a supply voltage of 24 to 48 volts DC and a power dissipation of 10.1 watts.

The Allen-Bradley Stratix 8000 switch has an open enclosure and uses 100 Base-F fiber optic Ethernet ports.

Modules are dcs-sis.com of the CompactFlash memory type and are rated at 2 amps inrush current.

The 1783-MX08F switch is 112 mm long, 97 mm wide, and 147 mm high.

To ensure optimal performance, it is recommended that users ensure that the ambient operating temperature range is between -40 degrees Celsius and 60 degrees Celsius.

The 1783-MX08F switch has a relative humidity range of 5% to 95% (non-condensing) and a maximum operating vibration of 2 G at 10 to 500 Hz.

It is rated for 20 G of operating shock and 30 G of non-operating shock.

The Allen-Bradley 1783-MX08F switch supports fiber optic Ethernet data rates of 100 Mbps.

The 1783-MX08F switch is optimized for IT and control/manufacturing control environments.

This makes the 1783-MX08F switch a high-performance managed Ethernet switch.

The 1783-MX08F Switch combines Cisco technology with innovative Allen-Bradley/Rockwell Automaton technology for high performance.

The 1783-MX08F switch is easy to set up and enables comprehensive diagnostic information within the specified Allen-Bradley/Rockwell Automation integrated architecture.

The 1783-MX08F switch provides users with the benefits of a CIP interface with predefined Logix tags and advanced configuration screens.

DESCRIPTION

The Allen-Bradley 1771-IR is a PLC5 resistance temperature detector (RTD) input module.

The module has six (6) input channels and is compatible with copper and platinum RTD types.

It is designed to support temperature measurements in Celsius and Fahrenheit units of measurement. It has a scan time of 50 milliseconds for six channels.

About the 1771-IR

The Allen-Bradley 1771-IR is a PLC-5 RTD input with a natural binary BDC supported data format for actual temperature and ohmic readings.

The unit does not require any type of external power supply. It consists of six three-wire RTD inputs.

The device’s channel update resolution introduces a combination of 50ms/6 channels and 16 bits + sign (1.0 degrees Celsius/1.0 degrees Fahrenheit/bit).

The 1771-IR input module has a voltage range of 100 ohms platinum and 10 ohms other. It has a backplane current range of 800mA.

The DC signal delay is 10ms in the on state, 50ms in the off state, and 45(+/- 15) ms in the AC signal delay in the on state.

These input modules have a lifetime of up to 100 million cycles as they meet voltage requirements of 10-276V AC.

The 1771-IR also helps protect your system by providing appropriate troubleshooting assistance. Module indicators show the status of smart inputs or dcs-sis.com outputs to help you troubleshoot your equipment.

The 1771-IR has an intelligent hybrid interface for connecting on/off devices such as switches, motor starters, pushbuttons, indicators and signalers.

This unique feature helps save on system engineering and spare parts as well as inventory and training costs.

The front panel of each AC discrete input/output module consists of bright status indicators.

The 1771-IR supports both Celsius and Fahrenheit measurement units. The platinum sensor has a temperature measurement range of -200 to +870 degrees Celsius and the copper sensor has a temperature measurement range of -200 to +260 degrees Celsius.

It has a resistance range of 1.00 to 600.00 ohms and a resolution of 0.1 degrees Celsius or 0.1 degrees Fahrenheit when used with a platinum sensor and 0.3 degrees Celsius or 0.5 degrees Fahrenheit.

The 1771-IR draws 950 mA at 5VDC from the backplane, consumes 4.75 watts, and has a thermal dissipation of 16.2 BTU/hour.

It is capable of open wire detection.

Description: Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive component.

The Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive assembly.

It is a 400VAC rated shaft module with a continuous current of 6.1 A and a peak current of 15.3 A. It has a 98% efficiency and a symmetrical 200.000 A (rms) short circuit current rating.

It has 98% efficiency and a symmetrical short circuit current rating of 200.000 A (rms).

About the 2094-BM01-M

The 2904-BM01-M is an Allen-Bradley component designed for use with Kinetix 6000 drives.

The drive is used as an axis module (AM), is in the 400 VAC voltage category, and has a continuous current of 6.1 A and a peak current of 15.3 A. The drive is designed for use with Kinetix 6000 inverters.

The 2904-BM01-M mounts directly to the Kinetix drive power rail. It is typically mounted next to the Integrated Axis Module (IAM) along the power rails, where the module draws power from the power rails to power its internal circuitry.

The axis module connects to the motor and motion device via feedback cables, auxiliary feedback cables, I/O, and safety wiring.

Axis modules also allow the installation of a control module so that control inputs can be integrated into the module.

The 2904-BM01-M features a 500 Hz bandwidth speed loop and 1300 Hz current loop frequency and a 4 kHz pulse width modulation (PWM) frequency.

The module has a built-in internal shunt with 50 W continuous power, 5.6 kW peak power, and an internal closure resistor rated at 115 Ohms.

The voltage rating is 805VDC with the shunt on and 765VDC with the shunt off.

The efficiency of the module is 98% with a capacitance of 150 ?F and capacitive energy adsorption of 19 joules.

The rated power output of the module is 57 watts (20%), 75% (40%), 90% (60%), 108 watts (8%) and 126 watts (100% load).

These power output data can be used for computer cabinet ventilation purposes.

With its modular design and embedded safety features, the 2094-BM01-M inverter is easy to maintain and offers greater flexibility.

It also simplifies wiring, reduces inventory, and can be modified using advanced technology.

It reduces energy and production waste and improves operational efficiency through its Safe Speed feature.

Its embedded advanced safety features also help protect personnel. Other safety features include safe maximum speed, safe maximum acceleration monitoring,

Safe Direction Monitoring, Zero Speed Monitoring, Enable Switch Control, and Door Monitoring and Control.

The 2094-BM01-Mhas enhanced diagnostic features that indicate the nature of a fault by displaying an error message.

Description

The Allen-Bradley 1747-SDN is an SLC 500 DeviceNet scanner module.

The module communicates with DeviceNet adapter modules connected to a DeviceNet network.

It is compatible with SLC 5/02 or later controllers. It is a single-slot module that supports operation in slave mode and passes dcs-sis.com messages in polled, pass-through, state change, cyclic I/O, and pass-through configurations.

It has a backplane current consumption of 5V DC, 500 mA.

About the 1747-SDN

The Allen-Bradley 1747-SDN is a DeviceNet communications scanner.

This scanner module is used to communicate with DeviceNet-enabled devices over a DeviceNet network or through a DeviceNet adapter module.

The module can operate in slave mode; send and receive messages in polled, select-through, state change, and cyclic I/O configurations.

It also supports a pass-through configuration where the 1747-SDN acts as a bridge and connects to a separate DeviceNet network.

This pass-through feature is intended to replace the 1770-KFD, 1784-PCD, 1784-PCID, or 1784-PCIDS DeviceNet connections on the network.

Specifically, the compatible SLC 500 processors when implementing the pass-through configuration are the SLC 5/03. SLC 5/04. and SLC 5/05.

The 1747-SDN supports configuration of up to 63 nodes at a baud rate of 125 Kbps. It draws 5V DC, 500 mA of backplane current.

The 1747-SDN has two (2) LED status indicators mounted on the front panel, such as the Module Indicator to report module operation and a Network Status LED to indicate the DeviceNet communication link.

It also has an LCD display that provides module address and error indications.The DeviceNet terminal is mounted behind the access door and is equipped with a 10-pin plug that plugs into the DeviceNet port.

The 1769-L30ER is a 5370 L3 CompactLogix controller with 1MB of user memory, dual Ethernet communication ports, and a single USB port.

The integrated communication ports support multi-node and point-to-point interfaces. Ethernet is the primary communication port used by this device to perform data exchange with a variety of devices.

This port supports linear, ring, and star topologies. Up to 16 nodes can be connected to this controller.

These nodes can consist of Human dcs-sis.com Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA), databases, converters, gateways, controllers, and other devices.

These embedded ports also act as embedded switches, which means that the same network traffic is experienced on the controller’s dual ports.

There are two (2) ways to assign an IP address to a controller. First, use Allen-Bradley’s BOOTP-DHCP utility.

This utility searches for a unique IP address for the device and assigns it the specified IP address.

The 1769-L30ER controller supports the installation of up to eight (8) 1769 Compact I/O modules.

In addition, up to three (3) expansion groups can be installed to further expand and maximize the functionality of the controller.

The controller is equipped with status indicators such as RUN, FORCE, BAT, OK, I/O. These LEDs are visible to the user and provide feedback on the controller’s operation.

DESCRIPTION

The 825-MCM20 is a currency converter module from Allen-Bradley.

It is part of the 825-P Motor Modular Protection System and is rated for 690 VAC (IEC) and 600 VAC (CSA/UL).

It has an inrush rating of 6 kV, an operating current range of 2.5-20 amps, a continuous thermal current of 24 amps, 

a saturation current rating of 240 amps, and a frequency rating of 50/60 Hz ± 3 Hz.

The converter has a PTC thermistor input and supports six (6) sensors in series.

About the 825-MCM20

The 825-MCM20 is Allen-Bradley’s currency converter module. It is part of the Bulletin 825-P Motor Protection System.

The device is designed primarily to protect industrial three-phase motors, providing thermal overload, 

PTC (positive temperature coefficient) overheat, undercurrent (load loss), current unbalance, and phase loss,

overcurrent (load jamming), short circuit, ground fault (residual), ground fault (zero sequence), 

frequency and other protective functions, as well as motor start/run and other motor start and run protection functions, such as a variety of motor start and run protection.

Protection prohibition at start, start motor timer, notch or pointing device, TCU (thermal capacity utilization) start prohibition, anti-reverse rotation timer, emergency start,

two-speed protection, reduced voltage start (star-delta) and stall switch.

The 825-MCM20 module is specifically designed for use in a variety of line starter applications,

especially low and medium voltage with 2 or 3 potential transformers, with or without phase current transformers,

with or without zero sequence core balancing current transformers, with or without external RTD module, reversing starters, star delta starters and two speed motors.

The 825-MCM20 operates in accordance with IEC and CSA/UL standards, specifically 690 VAC (IEC) and 600 VAC (CSA/UL), and is rated for dcs-sis.com 6 kV impact strength.

It has an operating current range of 2.5-20 amps with a continuous thermal current of 24 amps and a saturation current of 240 amps.

The module’s operating frequency range is 50/60 Hz ± 3 Hz. The module provides five (5) discrete inputs; one (1) C-type input; and one (1) C-type input.

The module provides five (5) discrete inputs; one (1) Type C, one (1) Type A, and release contact outputs as well as PTC thermistor inputs for up to six (6) PTC sensors in series.

The Allen-Bradley 825-MCM20 825-M is a current converter device for use with the Allen-Bradley 825 Modular Motor Protection System.

It is specifically designed to protect and manage three-phase industrial motors by monitoring motor current, line voltage, and temperature.

The 825-MCM20 has an operating (working) CSA/UL rating of 600V AC, an IEC rating of 690V AC, and a rated frequency range of 50-60 Hz +/- 3 Hz.

The converter has a functional current range of 2.5A to 20A with a continuous thermal current of 24A and a saturation current of 240A.

It has a converter impulse strength rating of 6kV and a frequency range of 50-60 Hz +/- 3Hz.

DESCRIPTION: The Allen-Bradley 825-P is a motor relay used as a protective device for three-phase motors.

It has standard protection features such as thermal overload (thermal model, PTC (positive temperature coefficient), overheat, undercurrent (load loss),

current unbalance and phase loss, overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency. This unit requires 110-240VAC power input.

About the 825-P

The 825-P is a protective relay for use with three-phase motors. Manufactured by Allen-Bradley, the device is

It provides standard protections such as thermal overload (thermal modeling), PTC (positive temperature coefficient), overheat, undercurrent (load loss), current imbalance, and phase loss.

overcurrent (load seizure), short dcs-sis.com circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency.

For motor start/run protection, this motor relay is capable of starting the motor timer via a protection disable during startup, a startup

notch or pointing device, TCU (Thermal Capacity Utilization) start inhibit, anti-reverse spin timer, emergency start, two-speed protection, reduced voltage start (star-delta), and stall switching to protect the motor.

It can be fitted with RTD-based protection via the 825-PR12D RTD RTD scanner, where up to twelve (12) RTDs can be connected and monitored.

The 825-P is also capable of monitoring event summaries that include information such as relay ID, date and time, trip triggers, and current and voltage amplitudes.

It can also monitor the Serialized Event Record (SER) and motor runtime and history of the last reset and start cycle since the last reset.

Emergency start cycles since the last reset can also be monitored by the unit, which also incorporates a full suite of metering functions.

The 825-P can optionally be fitted with an I/O channel consisting of one (1) 4-20 mA analog output, three (3) control inputs and four (4) contact outputs.

Additional communication interfaces can be installed, including adapters for DeviceNet and Modbus protocols.

The 825-P’s relay outputs also have a 4kV surge strength with a pickup time of < 10ms and provide an insulation voltage rating of 300V AC.

The system has 120V AC/DC (825-PIOD) inputs, a steady state current of 15mA at 2mA and 0.2mA on/off state currents, and on-state and off-state voltages of 15V and 5V respectively.

The system features thermal overload protection and optional voltage-based protection (overvoltage, reactive power, phase inversion, and undervoltage).

The 825-P has a modular construction with a built-in fixed keypad on the front panel and an LCD status display with LED status indicators.

It uses DeviceNet communication options at 125. 250. or 500kbps over distances of 500m, 200m, or 100m and is enclosed in a NEMA 4 (IP65) rated enclosure.

It has an operating temperature of -4 to +140 degrees Fahrenheit, a non-condensing relative humidity of 5% to 95%, and a storage temperature of -40 to +185 degrees Fahrenheit.

It weighs approximately 6.46 kilograms (including power supply and converter modules) and is CE, UL, and CSA listed.

Descripción

The 2093-AC05-MP1 drive is an Allen-Bradley/Rockwell Automation Kinetix 2000 Series multi-axis servo drive.

It is also an Integrated Axis Module type servo drive. 2093-AC05-MP1 Multi-Axis Servo Drives require clearance on the top and bottom for air-cooling, but not on the left or right sides.

This servo drive can be used with compatible SERCOS fiber optic cables.The 2093-AC05-MP1 Multi-Axis Servo Drive has a three-phase mains input voltage range of 170 to 264 volts AC.

About the 2093-AC05-MP1

The Kinetix 2000 Multi-Axis Servo Drives have output power requirements between 3 – 45 kW (4 – 49 amps) and are designed to provide Kinetix integrated motion solutions for applications.

Kinetix 2000 multi-axis servo dcs-sis.com drives are available in several series, including the 2093-AC05-MPx, 2093-AM0x, 2093-AMPx, 2093-ASP06.

2093-PRSxx, 2093-PRF, 2094-AL09. 2094-AL15S, 2094-AL25S, 2094-AL50S,

2094-AL75S, and 2094-AL75S-C2. 2093-AC05-MPx is a family of Kinetix 2000 multi-axis servo drives.

It includes the 2093-AC05-MP1. 2093-AC05-MP2. and 2093-AC05-MP5.The 2093-AC05-MP1 consists of one specific assembly.

The 2093-AC05-MP1 consists of a specific assembly that includes the Integrated Axis Module (IAM) mounted on the power rails and is a 230 VAC power converter and inverter.

The power rails (PR) consist of copper bus bars and circuit boards with connectors for each module.

The power rail provides power and control signals from the inverter section to the adjacent inverter, which also consists of compatible servo motors (low inertia, food grade, and stainless steel) and compatible linear actuators.