Category: A-B

Installation requirements

This device is intended for overvoltage applications of category II in industrial environments of pollution class 2 (as defined in IEC publication 60664-1).

The device must be mounted vertically as it contains a heat sink. Any other mounting angle will reduce the heat dissipation capability of the device and may result in premature failure of critical components.

The device can be mounted anywhere as long as the ambient temperature does not exceed the rated ambient conditions or clearance requirements.

Clearance requirements for CGCM equipment are

– 63.5 mm (2.5 inches) of clearance is dcs-sis.com required on both sides of the unit when mounted.

– 101.6 mm (4 in.) clearance is required above and below the unit when mounted.

Electrical Connections

The connection of the CGCM device depends on the application and the excitation programme. It is not possible to use all inputs or outputs in a given installation. Incorrect wiring may result in damage to the equipment.

Connect the terminals of the CGCM unit with copper wire rated at no less than 600V. General purpose wire rated for a minimum temperature of 105 °C (221 °F) may be used.

All wire must be copper. Select circuit wires according to good design practice.

The wire gauge ranges listed in the terminal block label instruction table indicate the physical capabilities of the connector.

Terminals for CGCM devices are located on the front, bottom, and right side panels of the device.

The nine-pin connector on the bottom of the unit is used for communication between CGCM devices in a redundant system. The recommended torque for the terminal screws is 1 N-m (9 lb-in).

Terminals that are used as shield wire landings are found on multiple terminal strips. Shielded terminals with the same name are connected together internally, but are not connected to a protective ground or any internal device circuit.

Product Description

The Allen-Bradley 6180P-15KSXP display computer is part of the VersaView Plus series and features a keypad and a 15-inch display.

The display supports full colour graphics. The keypad includes alphanumeric keys and several function keys.The 6180P-15KSXP display computer can be panel mounted on a machine system.

About the 6180P-15KSXP

The Allen-Bradley 6180P-15KSXP is a VersaView Plus 1500P standard package integrated display industrial computer with keypad input.

The computer’s keyboard includes not only alphanumeric keys, but also 44 function keys.

It has a 15-inch screen with 256K colour active matrix thin-film transistor (TFT) type.

Its display area is 12 x 9 inches with an aspect ratio of 4:3. The screen has a native resolution of 1024 x 768. The response time is 20 ms.

The 6180P-15KSXP measures approximately 13.97 x 19.01 x 8.86 inches and weighs 38.8 pounds.

The computer is panel mountable only and is rated NEMA 1/4/12.IP66.

It comes with 2 GB of RAM and two DIMM dual-channel DDR II slots, each with up to 2 GB of RAM for a total of 4 GB.

In addition, the computer is equipped with Caps Lock, Power/Standby, NumLock, and HDD/ODD/FD activity status indicators.

The computer has several I/O ports available, namely 2 serial ports, 1 parallel port, 2 front USB ports, 4 USB ports and 1 DVI port.

The 6180P-15KSXP also has 2 full-length and 1 half-length PCI expansion slots (5V I/O, PCI 2.2) and 1 full-length ISA expansion slot.

There are also two RJ45 Ethernet LAN ports supporting 10/100/1000 Mbps.

Audio jacks include a line-in jack, a line-out jack, and a microphone jack.

Description

The 2094-BC07-M05 is an n integrated axis module that is part of the Kinetix 6000 multi-axis drive.

The module is 400 V class with converter and inverter ratings of 45 kW and 49 a. The module has a power consumption of 71-226 watts. It does not have an integrated Safe Torque Off (STO) feature.

About 2094-BC07-M05

The 2094-BC07-M05 is a multi-axis servo drive that belongs to the Kinetix 6000 product category.

The drive has an input voltage range of 324-528 Vrms, 3-phase, a nominal power supply range of 360 VAC-480 VAC, and an input frequency of 47-63 Hz.

And the control power supply AC voltage is dcs-sis.com designed for 95-264 VACrms, 1 phase, with a nominal supply range of 110-240 VACrms.

It has a maximum input current of 71.0 (rms) amps and a maximum inrush current (0-pk) of 62.2 amps.

The module’s DC input voltage range (common bus follower) is 458-747 V DC, while the DC input current (common bus follower) is 67.7 A. The module has a maximum input current of 71.0 (rms) amps, while the maximum inrush current (0-pk) is 62.2 amps.

The servo drive has a continuous output power to the bus of 45 kW, while the a-series drives have a peak output power of 90 kW.

The B, S and D series drives have a maximum output power of 135 kW and an efficiency of 97 per cent.

Similarly, the drives have a continuous output current to the bus of 67.7 amps and a peak output current to the bus of 135 amps.

Series A drives are 4 amps and Series B, C and D drives are 203.2 amps.

The bus voltage rating for this driver is 825 VDC with a bus undervoltage of 275 VDC. the internal circuits have a continuous power rating of 200 W and a peak power rating of 22.5 kW.

The appropriate internal circuit resistor has a resistance value of 28.75 . It is symmetrical with a converter inductance of 75H, an inverter capacitance of 1410F and a short-circuit current rating of 200.000 A (rms).

Description.

The 1785-L80B is an Allen-Bradley Enhanced PLC5 programmable logic controller (PLC).

The controller has 100.000 words of embedded user memory and is equipped with several communication interfaces.

Examples include four (4) DH/Remote I/O (adapters or scanners), one (1) configurable RS-232. -423. and RS-422A compatible serial port, and two (2) programming terminals.

It can accommodate up to 3072 arbitrary mixes or 3072 inputs and 3072 outputs in free mode!

About the 1785-L80B

The Programmable Controller 1785-L80B is the core dcs-sis.com component of every control system based on the Allen-Bradley PLC-5 Series.

The 1785-L80B connects local, expansion, and remote I/O modules on a variety of communication interfaces into a single control system.

There are four built-in ports on the 1785-L80B controller. The ports are labelled Channel 1A, Channel 1B, Channel 2A and Channel 2B.

All ports can be configured as remote I/O scanners, remote I/O adapters, and DH communication interfaces.

DH communications can be used both for remote programming and monitoring of the 1785-L80B and for creating peer-to-peer communication networks between various PLC-5 controllers.

The Remote I/O connection is used for real-time data exchange between the controller and I/O, operator interface and other functions.

All four channels on the 1785-L80B can be used as either remote I/O scanners or remote I/O communications adapters.

The 1785-L80B is designed with multiple communication interfaces that can be used to communicate with different automation devices simultaneously.

It has four (4) DH/Remote I/Os (adapters or scanners) labelled CH1A, CH1B; CH2A and CH2B;.

One (1) configurable serial port for RS-232 and RS-422A electrical standards supporting the DF1 protocol, and two (2) programming terminals.

The 1785-L80B is capable of communicating with up to 93 I/O chassis and up to 32 Remote I/O (RIO) racks.

Enhanced PLC 5 controllers, such as the 1785-L80B, are primarily used when the control system needs to communicate with a large number of remote I/O (RIO) devices and when connecting to a large number of Data Highway+ (DH) devices.

For installation, the 1785-L80B can be mounted in the 1771-A1B, 1771-A2B, 1771-A3B, 1717-A3B1. and 1771-A4B PLC5 chassis.

Power supplies supported by this processor include the 1770-P1. 1770-P45. 1770-P5. 1771-PE, 1771-P4S1. 1771-P6S1. 771-P4R, and 1771-P5R.

It is also used to configure I/O modules and expansion racks.

DESCRIPTION

The Allen-Bradley 1394-SJT22-A is a GMC standard system module with a /-10VDC input.

The module requires an input voltage of 380/460 volts AC, three phase, an input frequency of 50/60 Hz, and a current of 28.6 amps.

It has an electrical output voltage of 530/680 V DC and a continuous power output of 17/22 kW with a peak power of 136 kW.

The continuous current output is 33.8 A and the peak current is 200.0 amps.

About the 1394-SJT22-A

The 1394-SJT22-A is a 1394 GMC Turbo system module that is part of the Allen-Bradley 1394 multi-axis motion control system.

The system module is primarily used for analogue servo dcs-sis.com systems and provides digital servo drives with a /-10VDC interface.

The system module is mounted on the far left side of the 1394 assembly, which includes the axis modules, bus connectors, and termination resistors.

Each module is mounted via a slide-lock mechanism and fasteners that are precisely aligned with each other.

The system module uses RS232/422 communication and supports the DH485 communication protocol. It can optionally be fitted with Remote I/O communication (RIO) and AxisLink communication interfaces.

When installing this system module or any other product in a 1394 system, the ambient temperature of the mounting location must be no higher than 50.0 degrees Celsius and mounted on a flat, stable vertical surface.

The mounting panel must have minimal shock and vibration, and the environment must be free of moisture, oil, dust, and corrosive gases.

This system module is not equipped with an internal shunt resistor. An external shunt module must be installed.

Compatible shunt resistors include the 1394-SR9A, -SR9AF, -SR36A, or -SR36AF manufactured by Allen-Bradley.

The shunt module generates a significant amount of heat. Because hot air rises naturally, instruments or components that may be affected by hot air must not be mounted on top of the external shunt module.

The top clearance must be 254 mm (10.0 inches) and 155 mm (6.1 inches) on both sides, including the bottom area of the system module.

The Allen-Bradley 2094-BL02 module is a line interface module that is part of the 2094 Kinetix 6000 product line.

It operates at three-phase voltages from 400 to 460 volts AC and a current rating of 30 amps.

The module has an internal control line filter rating of 230 volts AC.

The 2094-BL02 module is a line interface module manufactured by Allen-Bradley/Rockwell Automation as part of the 2094 Kinetix 6000 product line.

The module has a three-phase voltage rating of 400 to 460 volts AC, a current rating of 30 amps, and an internal control line filter rated at 230 volts AC.

It also has a 24-volt DC power supply output voltage with a current capacity of 8 amps.

The 2094-BL02 Line Interface Module comes with components such as connector sets for the 2094-ALxxS, BLxxS and XL75S-Cx modules.

These items include the volt AC line (IPL), input/output (IOL), control power supply (CPL), and volt AC load (OPL),

230-volt auxiliary output (P2L), 24-volt brake input/output power (P1L), and auxiliary 230-volt input (APL) connectors.

The Allen-Bradley 2094-BL02 module also dcs-sis.com features a connector set for the 2094-AL09 and 2094-BL 02 line interface modules that

This includes 24-volt brake input/output power (PSL), AC load (OPL), VAC line (IPL), and control power (CPL) connectors.

However, the I/O (26-pin) connectors for the 2094-BL02 and 2094-AL09 modules are not provided.

The 2094-BL02 line interface module has several requirements for proper installation.

It must be encapsulated in a grounded enclosure that provides protection in accordance with EN 60529 (IEC 529).

make the internal parts of the module inaccessible to unskilled operators, and meet CE and UL requirements.

The NEMA 4X enclosure meets or exceeds all of these requirements and provides an IP 66 rating.

Panels installed in the enclosure for mounting system components should be on a hard, flat, vertical surface that is not subject to moisture, shock, or vibration.

This surface will not be subject to moisture, shock, oil mist, vibration, corrosive vapours or dust.

Product Description: Allen-Bradley 2198-S086-ERS3

The Allen-Bradley 2198-S086-ERS3 features 29.7 kW continuous output power, 22-40 lb*in (2.5-4.5 N*m) torque values, and 560 microfarads of internal capacitance.

About the 2198-S086-ERS3

Allen-Bradley’s 2198-S086-ERS3 Kinetix 5700 single-axis frequency converter is a single-axis frequency converter module that is

for controlling machines with high shaft counts and dcs-sis.com high power requirements. The inverter has current/speed loop bandwidths of 100Hz and 400Hz.

The inverter has a current/speed loop bandwidth of 100 Hz and 400 Hz, a pulse width modulation (PWM) frequency of 4000 Hz, and a continuous output current of 43 A and a 0-pk output current of 60.8 A.

The peak values of continuous and 0-pk output currents are 86A and 121.6A, respectively, and the rated output power of the inverter is 29.7KW.

It requires a DC input current of 45.7ADC and has an internal capacitance of 560μF.

The 2198-S086-ERS3 is rated at 4.6A for non-braked servo motors.

The rated control power for a braked servomotor is 9.6A, and the inrush power at startup is 4A.

Rated power output percentage is 190 watts at 20%, 225 watts at 40%, 325 watts at 60%, 300 watts at 80%, 300 watts at 100

It has a maximum power dissipation of 190 watts at 20% of rated power output, 225 watts at 40%, 325 watts at 60%, 300 watts at 80%, and 475 watts at 100%.

The 2198-S086-ERS3 has an operating temperature range of 0 to 50 °C (32 to 122 °F) and a humidity limit of 5 to 95% non-condensing.

It can be stored over a temperature range of -40 to 70 °C (-40 to 158 °F). Even when installed at an altitude of 1.500 meters (4.921 feet), the

Even when installed at an altitude of 1500 meters (4921 feet), it will not be downgraded and will maintain optimal functioning under 2 G of operating vibration and 15 G of shock.

The 2198-S086-ERS3 provides motor and auxiliary feedback through feedback connections on the 2-pin Motor Feedback (MF) connector and 15-pin Universal Feedback (UFB) connector.

It also supports EtherNet network connectivity through the Ethernet port on the inverter and a 0.15-meter (6-inch) Ethernet cable.

Description:

The Allen Bradley 1444-DYN04-01RA module is part of the Allen-Bradley Dynamax family of intelligent I/O modules.

It is designed to provide the integrated and distributed solution needed to monitor and control critical industrial machinery.

The 1444-DYN04-01RA module monitors and protects pumps, motors, gearboxes, fans, gas and steam turbines, high-speed compressors, and other reciprocating or rotating machines.

About 1444-DYN04-01RA

The Allen-Bradley 1444-DYN04-01RA module is part of the Allen-Bradley Dynamax family of intelligent I/O modules.

It is used to provide the integrated and distributed solution dcs-sis.com needed to monitor and control critical machinery.

The 1444-DYN04-01RA module monitors and protects pumps, motors, gearboxes, fans, gas and steam turbines,

high-speed compressors, and other reciprocating or rotating machines. In addition to this, the 1444-DYN04-01RA module measures strain or pressure,

In addition, the 1444-DYN04-01RA module can also measure dynamic signals such as strain or pressure, vibration, and position measurement signals such as rod position, differential expansion or thrust.

The 1444-DYN04-01RA module allows real-time measurements to protect machinery from imminent failure.

In addition, the measurement results can be further processed to calculate the acute fault indication parameters required to assess the current and predicted health of the machine.

The 1444-DYN04-01RA module can be managed and configured via a Logix controller and connected via an EtherNet/IP industrial network.

As with the rest of the Allen-Bradley/Rockwell Automation Integrated Architecture system, the

As with other parts of the Allen-Bradley/Rockwell Automation Integrated Architecture system, other system components such as visualisation products, controllers, and I/O products can be applied to the 1444-DYN04-01RA module to meet specific needs and applications.

The 1746sc-INO4I draws 5 volts DC from the backplane. This consumption rating is the same when the module is powered externally. The module has a removable 16-bit terminal block that accommodates Belden 8761 shielded twisted-pair cable. 1746sc-INO4I has 16-bit resolution, 366 nano-amps per count, and 320 microvolts per count. 1746sc-INO4I isolated channel analogue output models have auto-calibrating programmable limits and safety states, and are optically isolated for The 1746sc-INO4I isolated channel analogue output model has auto-calibrated programmable limits and safety states, and is opto-isolated to 750 volts DC (channel-to-channel, field wiring to backplane). 1746sc-INO4I is rated for thermal power dissipation up to 4.5 watts, with a maximum update time of 33.7 milliseconds for all 4 parallel channels, and a step response time of 1 millisecond. In addition, the 1746sc-INO4I is UL/CUL Class I, Division 2. Groups A, B, C, D, and CE listed.

Part number 1746sc-INO4I SLC 500 compatible module dcs-sis.com is an analogue output module manufactured by spectrum control. This module is manufactured by Spectrum Controls, an Allen-Bradley partner.

Encompass Partners is an Allen-Bradley approved and certified partner to provide Allen-Bradley compatible products.

This module is similar in appearance to the actual SLC 500 module. The module has four (4) differential analogue output channels providing 0-20 mA, 0-21 mA, 4-20 mA at 366 nA per count with 16-bit resolution.The module features extended output ranges, auto-calibration, programmable limits, and safety status. The module’s data can be formatted into 16-bit binary, scaled engineering units, PID scaling, 1746-NO4 format, and user-defined proportional counts. Its accuracy is 0.08 per cent of full scale at 25 degrees Celsius and 0.15 per cent at 60 degrees Celsius.

Each channel of the module is galvanically isolated at 750 VDC, which improves system reliability by eliminating the noise crosstalk that occurs when converting the module’s high-resolution data. The same isolation level as the backplane field wiring provides protection for the rack and processor.

Since the module’s isolation eliminates the need for external signal isolation devices, system costs are reduced. The module’s single-slot width also saves critical chassis slots.

The module uses Allen-Bradley design and technology and functions like an Allen-Bradley module. Its configuration is similar to the SLC 500 module and most of its features are similar to the Allen-Bradley analogue output modules.

Allen-Bradley 1771-A4B is a general purpose I/O enclosure.

The Allen-Bradley 1771-A4B is a general purpose I/O chassis.

The hardware is a sixteen (16) slot chassis designed to provide backplane connections and to accommodate 1771 PLC modules.

It provides a maximum backplane current of 24 A and is designed for panel mounting. It has a total weight of 7.3 kg or 16 lbs.

About the 1771-A4B

The Allen-Bradley 1771-A4B is a general purpose I/O chassis that is part of the 1771 Programmable Logic Controller (PLC) product family.

The chassis has sixteen (16) I/O slots that contain dcs-sis.com electronic circuitry, specifically the backplane, which distributes power to the connected modules.

It is also equipped with hinges for field wiring arms.

The 1771-A4B has an operating temperature range of 32-140 degrees Fahrenheit or 0-60 degrees Celsius.

Hardware storage temperature is -40 to 185 degrees Fahrenheit or -40 to 85 degrees Celsius.

Relative humidity is 5-95% non-condensing. When installing this general purpose I/O chassis, panel vibration and shock should be kept within 2g and 15g at 10-500 Hz, respectively.

The 1771-A4B receives power from the 1771 processor and has an internal power supply that provides 2-4 amps,

The built-in power supply provides 2-4 amp, 3-8 amp rated output power modules, and an external power supply with 6.5-16 amp output current.

In general, do not install external power supplies and power supply modules on the 1771-A4B. Such power connections are incompatible and will result in a substandard hardware configuration.

The 1771-A4B chassis has 16 I/O slots. It measures 12.4 x 24 x 7.6 inches and weighs 14.8 pounds.

When installed in a 1771 PLC-5 system, it utilizes the backplane mounting method with adequate spacing and an open enclosure.

The backplane of the enclosure has a DC voltage of 5 volts and a current of 8 amps.