Archives

Features and benefits

• Pre-configured for use with System 800xA

• NE810 supports redundant power connection

• Enhanced monitoring using PNSM

• Industrial Ethernet 10-port switch

• Long life duration

• Fully supported by ABB

NE810 is an Industrial switch made for harsh environments. Due to

our multi-rate SFP solution, the switch can be used in either 100

Mbit or Gigabit networks. Our unique FRNT (Fast Recovery of

Network Topology) technology is the fastest protocol on the

market to re-configure a network in case of any link or hardware

failure. That is why NE810 is also used in safety-critical applications

such as tunnels, traffic signal control, and railway systems.

Installations in harsh environments and places with heavy electrical

interference require the use of reliable media. NE810 provides a

number of solutions using fiber optic transceivers. Multi- or singlemode

transceivers can be used to build point-to-point or

redundant ring networks with ranges up to 120 km between each switch. 

NE802 is an unmanaged 5-port switch with one SFP fibre port and

four copper ports, al supporting 10/100 Mbit/s or Gbit Ethernet. The

ABB range of Smal Form-factor Pluggable (SFP) transceivers are

available as multimode, singlemode or Bi-Di transceivers with

distance up to 120 km.

The unit is designed for use in industrial applications with dual 10 to

57 VDC power input. The unique “tri-galvanic” isolation provides

isolation between al ports, power supply and between each chassis

screen avoiding ground loop currents. The IP21 rating ensures that

the unit can be instaled in locations where condensed water may

occur. Only industrial grade components are used which gives the

units an MTBF of 1.182.000 hours and ensures a long service life. A

wide operating temperature range of –40 to +70 °C (–40 to +158 °F)

can be achieved with no moving parts.

Features and benefits

• TX shields individualy isolated

• Wide DC power range 12 – 48 VDC

• Wide temperature range

• Automatic MDI/MDI-X crossover

• LED indicators for Power, Speed, Duplex, Link and Traffic

• Port monitoring

• 35 mm DIN rail mounting

• Enable or disable of flow control

NE802 is an unmanaged 5-port switch with one SFP fibre port and

four copper ports, al supporting 10/100 Mbit/s or Gbit Ethernet. The

ABB range of Smal Form-factor Pluggable (SFP) transceivers are

available as multimode, singlemode or Bi-Di transceivers with

distance up to 120 km.

NE810 is an Industrial switch made for harsh environments. Due to

our multi-rate SFP solution, the switch can be used in either 100

Mbit or Gigabit networks. Our unique FRNT (Fast Recovery of

Network Topology) technology is the fastest protocol on the

market to re-configure a network in case of any link or hardware

failure. That is why NE810 is also used in safety-critical applications

such as tunnels, traffic signal control, and railway systems.

Installations in harsh environments and places with heavy electrical

interference require the use of reliable media. NE810 provides a

number of solutions using fiber optic transceivers. Multi- or singlemode

transceivers can be used to build point-to-point or

redundant ring networks with ranges up to 120 km between each

switch. Our BIDI transceiver, which transmits and receives data on

a single fiber can be used in applications where the number of fiber

cores is limited.

Real-time properties are implemented in the switch in order to

achieve determinism for real-time critical applications. NE810

supports QoS (Quality of Service) with four priority queues and

strict priority scheduling as well as HoL (Head of Line Blocking

Prevention). All to assure that the data network is deterministic.

ABB PT805 3BSE080216R1 Single mode

ABB PT806 3BSE080227R1 Single mode,BiDi

ABB PT807 3BSE080228R1 Single mode,BiDi

ABB PT808 3BSE080217R1 Single mode

ABB PT809 3BSE080235R1 Single mode,BiDi

ABB PT810 3BSE080236R1 Single mode,BiDi

ABB PT811 3BSE080218R1 Single mode

ABB PT812 3BSE080233R1 Single mode,BiDi

ABB PT813 3BSE080234R1 Single mode.BiDi

ABB PT814 3BSE080232R1 RJ45 System 800xA hardware selector

ABB PT831 3BSE080222R1 Multi mode

ABB PT832 3BSE080225R1 Multi mode

ABB PT833 3BSE080219R1 Single mode

ABB PT834 3BSE080229R1 Single mode,BiDi

ABB PT835 3BSE080230R1 Single mode,BiDi

A PC with PCM600 can be connected to any 615 series IED within a station by

using the Ethernet connection. The connection can also be used for service and

maintenance purposes. In addition, the connection is used to handle disturbance

records from the protection IEDs using the IEC 61850 file transfer.

The modern-day IEDs are designed using the concept of the IEC 61850 standard.

This is primarily in regards to how functions within the IED are modelled and how

the IED is represented in the substation. See the IEC 61850 parameter list for the

list of logical nodes available in the IED and observe how they follow the structure

and rules as defined in part 7 of the standard.

The engineering of the used communication protocols is a separate task and an

addition to the engineering of protection and control functions.

PCM600 can be used for different purposes throughout the IED life cycle. A set of

special tools is available for different applications.

Connectivity Packages are separate software packages that provide type and

version information to PCM600. Further Connectivity Packages assist the tool with

communications.

PCM600 uses IEC 61850 over Ethernet to communicate with bay IEDs. This

communication allows PCM600 to configure and monitor the IEDs. In addition to

IEC 61850 the IEDs have optional communications protocols and hardware to

connect to station engineering tools. PCM600 provides the ability to export the

configuration of the IEDs or entire substation in a standard file format which

allows for station engineering.

A PC with PCM600 can be connected to any 615 series IED within a station by

using the Ethernet connection. The connection can also be used for service and

maintenance purposes. In addition, the connection is used to handle disturbance

records from the protection IEDs using the IEC 61850 file transfer.

Protection and Control IED Manager PCM600 offers all the necessary functionality

to work throughout all stages of the IED life cycle.

• Planning

• Engineering

• Commissioning

• Operation and disturbance handling

• Functional analysis

With the individual tool components, you can perform different tasks and functions

and control the whole substation. PCM600 can operate with many different

topologies, depending on the customer needs.

PCM600 is used to conduct complete engineering and configuration activities

needed for the bay level IEDs.

PCM600 uses IEC 61850 over Ethernet to communicate with bay IEDs. This

communication allows PCM600 to configure and monitor the IEDs. In addition to

IEC 61850 the IEDs have optional communications protocols and hardware to

connect to station engineering tools. PCM600 provides the ability to export the

configuration of the IEDs or entire substation in a standard file format which

allows for station engineering.

The standard supports free allocation of functions to devices. With efficient

communication facilities, the functions can be located anywhere in the system, that

is, an interlocking function can reside in the IED or on the station level.

Additionally, the standard is open for different system implementations, that is,

different integration levels and allocation of functions to different devices is

supported.

The standard also defines an XML description language for substation automation

systems. The language facilitates efficient integration of devices into systems in an

automated fashion. Additionally the standard supports a comprehensive and

consistent system definition and engineering, which makes not only the devices,

but also their tools and systems interoperable (standard part 6).

The standard uses Ethernet and TCP/IP for communication. Since Ethernet and TCP/

IP are widely accepted and used, the application of these technologies provide a

broad range of features from mainstream communication (standard parts 8-1. 9-2).

However, IEC 61850 is also open for possible new communication concepts in the

future.

The IEC 61850 standard specifies an expandable data model and services for

substation automation (standard parts 7-x). The standard does not specify any

protection or control functions, but specifies how the functions expose their

information to a communication network.

The standard supports free allocation of functions to devices. With efficient

communication facilities, the functions can be located anywhere in the system, that

is, an interlocking function can reside in the IED or on the station level.

Additionally, the standard is open for different system implementations, that is,

different integration levels and allocation of functions to different devices is

supported.

The standard also defines an XML description language for substation automation

systems. The language facilitates efficient integration of devices into systems in an

automated fashion. Additionally the standard supports a comprehensive and

consistent system definition and engineering, which makes not only the devices,

but also their tools and systems interoperable (standard part 6).