Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0
April 15, 2026 BY
IN Emerson

Emerson 00813-0100-0115 Designed for Visualisation

Designed for Visualisation

RXi – Industrial monitors are designed with precision in mind when it comes to visualisation.

Multi-touch, projected capacitive screens feature high resolution,

vivid graphics capabilities and fast response times to ensure relevant

information is always available for viewing and interaction.

This enables operators to make faster, more informed decisions

with a high-performance platform that reduces total cost of ownership.

Anywhere, anytime: a wide range of applications

The portfolio operates efficiently in temperatures as high as 65°C and as low as -20°C. 

The modules can be used outdoors and are available in a variety of configurations.

Modules can be used outdoors and are equipped with sunlight-readable (SLR)

Readable (SLR) UV-protected screens.The screens of the RXi – Industrial Monitors

are strictly IP66 certified and are protected against dust, humidity and even direct water spray.
April 15, 2026 BY
IN HIMA

HIMA X-CPU 01 Processor Module Function

The following elements also contribute to the safety function:

Hardware self-test

Safe communication with I/O modules

Reaction in the event of a fault

If the test harness detects a fault, the processor module enters the ERROR STOP state and restarts.

Diagnostic information is available to find the cause of the fault.

Start-up after error stop

If the cause of the fault still exists, the processor module avoids restarting and repeating the error stop:

After the first error stop, the processor module reboots normally and switches to system operation.

After the second error stop, the user must reboot the system using PADT after troubleshooting.

After the processor module has been running in system operation for approximately one minute,

the next error stop will be considered as the first error stop.

Scope of delivery

The module must be mounted on a suitable connection board to operate.

An Ethernet cable is required to connect the PADT.

The connection board and Ethernet cable are not included in the scope of delivery of the module.
April 15, 2026 BY
IN HIMA

HIMA Modernisation to HIQuad X brings additional benefits

Modernisation to HIQuad X brings additional benefits:

– Seamless modernisation

HIQuad inputs/outputs (including field wiring) can be left in place,

which reduces costs compared to new installations.

Software engineering is supported through automated logic conversions,

reducing engineering effort and potential sources of error.

– Reduced downtime

Unaltered components can be tested more easily,

reducing the downtime required for modernisation.

– Modernisation flexibility

You have complete freedom to carry out modernisation in a single step or in phases.

– Increased safety and security

HIQuad X provides you with the optimal basis for compliance of your system with

the latest functional safety standards of IEC 61511 and automation safety standards of IEC 62443.

– Better performance

State-of-the-art technology delivers better functionality, such as shorter cycle times,

increased heavy-duty capability, improved system availability, reduced engineering effort and improved

maintenance.

– Ongoing support:

Products entering the legacy phase have limited availability and do not receive updates

or new features. HIQuad X fully supports new safety features and future certifications.
April 15, 2026 BY
IN KEBA

KEBA KeControl C5 – FE 560 Multi-protocol fieldbus expansion card

Product features

// 1 x EtherCAT / EtherNet/IP / PROFINET

// Plug connection for

KeControl C5 control modules

Brief description

The Ethernet-based fieldbus card FE 560 can be connected on

the left of the KeControl C5 controllers using the Card Edge connector.

This allows the exchange and processing of process data between

the higher-level control and the KeControl C5 control.

All relevant protocols such as EtherCAT, EtherNet/IP and PROFINET are supported.
April 15, 2026 BY
IN KEBA

KEBA KeControl C5 – FE 560 Technical specifications

Technical specifications

Interfaces

KeControl C5 control module 1 x Card Edge connector

EtherCAT slave / EtherNet/IP adapter /

PROFINET IO-Device 2 x RJ45

Dimensions

Height 106 mm

Width 26.5 mm (when installed)

Depth 82.5 mm (snap-on height 77.5 mm)

Weight 95 g

Environmental conditions

Operating temperature 0 °C to +55 °C

Storage temperature-40 °C to +70 °C

Relative humidity 10 % to 95 % (non-condensing)

Vibration/shock resistance According to EN 61131-2

General data

Overvoltage category II

Protection class III according to EN 61010-2-201

Certification

CE 2014/30/EU and 2011/65/EU

UL UL 61010-1 and UL 61010-2-201

UKCA Conformity with relevant statutory requirements
April 15, 2026 BY
IN KEBA

KEBA KeControl C5 FE 57x Technical specifications

Technical specifications

Dimensions

Height 106 mm

Width 26.5 mm (when installed)

Depth 82.5 mm (snap-on height 77.5 mm)

Weight 95 g

Environmental conditions

Operating temperature 0 °C to +55 °C

Storage temperature-40 °C to +70 °C

Relative humidity 10 % to 95 % (non-condensing)

Vibration/shock resistance According to EN 61131-2

General data

Overvoltage category II

Protection class III according to EN 61010-2-201

Interfaces

FE 571 FE 573

KeControl C5 control module 1 x Card Edge connector

EtherCAT master 2 x RJ45 2 x M8

Certification

CE 2014/30/EU and 2011/65/EU

UL UL 61010-1 and UL 61010-2-201

UKCA Conformity with relevant statutory requirements
April 15, 2026 BY
IN KEBA

KEBA The FE 57x fieldbus master cards

Product features

// 2 x EtherCAT master interfaces

// Plug connection for

KeControl C5 control modules

Brief description

The FE 57x fieldbus master cards can be connected on the left of the

KeControl C5 controllers using the Card Edge connector.

They make it possible to create additional EtherCAT master interfaces

on the controller and thus an expansive set-up of plants and machines

through the use of numerous fieldbus components.

The EtherCAT interfaces can be supplied either with M8 or

with RJ45 connectors. Depending on the requirements,

this provides suitability for individual industrial applications.

The built-in switch supports a star topology of the EtherCAT

slaves without the need for additional hardware.
April 15, 2026 BY
IN KEBA

KEBA KeControl C5 – NE 551 Gbit Ethernet expansion card

Product features

// 2x Gbit Ethernet RJ45 interface

// Plug connection for

KeControl C5 control modules

Brief description

The NE 551 Gbit Ethernet cards can be connected on the left of the KeControl C5 CPUs using the Card

Edge connector. Internally, they are connected via PCI Express. NE 551 provides two independent

Ethernet interfaces.

Technical specifications

Dimensions

Height 106 mm

Width 26.5 mm (when installed)

Depth 82.5 mm (snap-on height 77.5 mm)

Weight 90 g

Environmental conditions

Operating temperature 0 °C to +55 °C

Storage temperature-40 °C to +70 °C

Relative humidity 10 % to 95 % (non-condensing)

Vibration/shock resistance According to EN 61131-2

Interfaces

KeControl C5 control module 1 x Card Edge connector

Ethernet Gbit 2 x RJ 45 (only 1 x RJ 45 usable with CP 50x)

General data

Overvoltage category II

Protection class III according to EN 61010-2-201

Certification

CE 2014/30/EU and 2011/65/EU

UL UL 61010-1 and UL 61010-2-201

UKCA Conformity with relevant statutory requirements
April 15, 2026 BY
IN KEBA

KEBA KeDrive D3 controls – D3-DU 3×5 Control modules with built-in safety control

D3-DU 335/A, D3-DU 335/B, D3-DU 365/A, D3-DU 365/B

Product features

// All-in-one controller in the form factor of the

KeDrive D3 drive technology

// Powerful and scalable

// Maximum flexibility through the free selection of fieldbuses

// Can be expanded with 1-axis, 2-axis or 3-axis controllers

// Built-in cross-axis safety control including safe I/Os

Brief description

The D3-DU control solution for PLCs, motion and robotics is extremely

powerful and offers maximum flexibility.

Numerous CPU types, from the Intel Atom 1.9 GHz to the Intel

Celeron 2 Ghz, enable an application-optimized computing performance

that allows drive control, visualization, graphics processing, closed-loop control,

and standardized PLCs to run on a single control at low cost.

The control comes with built-in safety control including safe I/Os.

The safety control is ideal for robotics applications.

In addition to safe fieldbus communication, it offers safe motion monitoring

of individual axes and simultaneous safe space monitoring (TCP, Tool Center Point).

A built-in service display provides support for the quick configuration

and diagnostics of the control, the safety control,and the drives.

The KeDrive D3 controls come either with a heatsink  (/A) or with

ColdPlate (/B), depending on the selected (multi-axis) drive controller type.

For more information on KeDrive D3 safety control, refer to the KeSafe product brochure.
April 15, 2026 BY
IN KEBA

KEBA KeDrive D3 controls – D3-DU 3×0 Control modules

D3-DU 330/A, D3-DU 330/B, D3-DU 360/A, D3-DU 360/B

Product features

// All-in-one controller in the form factor of the

KeDrive D3 drive technology

// Powerful and scalable

// Maximum flexibility through the free selection of

fieldbus

// Can be expanded with 1-axis, 2-axis or 3-axis

controllers

Brief description

The D3-DU control solution for PLCs, motion and robotics

is extremely powerful and offers maximum flexibility.

Numerous CPU types, from the Intel Atom 1.9 GHz to

the Intel Celeron 2 Ghz, enable an application-optimized computing

performance that allows drive control, visualization, closed-loop control,

and standardized PLCs to run on a single control at low cost.

A built-in service display provides support for the quick configuration

and diagnostics of the controls, and the drives.

The KeDrive D3 controls come either with a heatsink  (/A) or

with ColdPlate (/B), depending on the selected (multi-axis) drive controller type.

Menu

Search for products

Back to Top
Product has been added to your cart