The IC200ALG264 is a 15-point analogue current input module for the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now manufactured by Emerson Automation.

The module features fifteen (15) single-ended input channels that accept 4-20 mA and 0-20 mA input signals with 15-bit resolution** and an update rate of 7.5 ms.

The module has a **backplane current consumption of 100 mA.

About the IC200ALG264

The IC200ALG264 is the analogue input module in the VersaMax I/O product family of distributed I/O modules and components.

The IC200ALG264 is a compact, multifunctional input module designed to be mounted in a remote location and transmit I/O data via industrial dcs-sis.com communication protocols.

The module primarily features fifteen (15) analogue input channels designed to accept 0-20 mA and 4-20 mA input signals.

These input channels are equipped with separate analogue-to-digital converter (ADC) circuits with a digital conversion resolution of 15 bits and an analogue resolution of 0.5 µA.

The analogue resolution is 0.5 µA = 1 (4-20 mA range) and 0.625 µA = 1 count (0-20 mA range).

The module has an input accuracy of +/-0.5% (typical) and +/-0.25% of full scale** at an ambient temperature of 0-3 degrees Celsius.

+/-0.5% input accuracy (typical) and +/-0.25% full scale** at 0-3 degrees Celsius ambient temperature, and +/-60% full scale** at 1-0 degrees Celsius ambient temperature.

The IC200ALG264 is capable of detecting error conditions such as internal power loss in both operating modes and open circuit detection when operating in 4-20 mA mode only.

These diagnostic conditions are reported to the CPU for error indication and correctly displayed to the Human Machine Interface (HMI) and Supervisory Control and Data Acquisition (SCADA) systems.

The module’s operating mode or range selection is set by using terminal jumpers. To configure 4-20 mA, the terminal jumpers must be unloaded, which is the default configuration.

Otherwise, install the jumper for 0-20 mA operation.

The IC200ALG264 has a built-in module OK LED status indicator.Tis LED indicates that the module has successfully powered up and downloaded using a valid configuration.

It has a ** backplane current consumption of 100 mA.

The IC200ALG264 module is an analogue input module designed and marketed by GE Fanuc Automation.

This particular module is part of the Versamax family of I/O modules. It provides interfaces for 15 different current inputs, enabling different devices to be connected to the main processor.

The module works perfectly when using the backplane power supply. User transceivers connected to the module require an external power supply.

The GE Fanuc Automation IC200ALG264 analogue input module offers different diagnostic functions that can detect internal power losses used for field circuits.

It can also report open-circuit faults on each of its channels. These diagnostic modes are available when used in 4-channel 20 mA mode.

The GE Fanuc IC200MDD846 module is a hybrid I/O module.

It is manufactured by GE Fanuc and is part of the Versamax product family. It helps increase device flexibility by integrating discrete input and output points into a single module.

About the IC200MDD846

The GE Fanuc IC200MDD846 Hybrid I/O Module is a GE Fanuc product that is part of the Versamax family.

The module is designed to increase machine flexibility by integrating discrete input and output points into a single module.

For the module to operate efficiently, the IC200CHSxxx carrier base is required.

The IC200MDD846 hybrid module has a set of 8 input points that draw current from the input devices connected to it and send it to the common line.

It also has a set of 8 output points with 8 output points capable of handling 2 Amp** current loads.

The input points of this hybrid module are positive logic type or source line type inputs, while the output points are type A relays which come with silver contacts, fixed coils and moving frames.

Each output point of the IC200MDD846 module is isolated. The module also features LED indicators corresponding to each input and output point.

The LEDs indicate that the device is switched on and off, while the ‘OK’ LED indicates the presence of baseboard power.

The IC200MDD846 Versamax Hybrid Module draws all necessary power from the rack mount backplane.

It is rated to supply 300 mA** and has a nominal input voltage of 120 volts AC.

It also has nominal output voltages of 5 volts DC, 24 volts DC or 125 volts DC and 120 volts AC or 240 volts AC.

The module has a voltage drop of 0.3 volts. A network interface unit or CPU is required to perform device processing.

The Discrete Hybrid Module combines inputs and outputs in a compact module to provide maximum flexibility.

Discrete input modules receive signals from input devices such as sensors, pushbuttons, and switches.

Signals from input devices such as pushbuttons and switches that have two states: on or off, open or closed.

Discrete output modules send control signals to devices that also have two states, such as contactors, indicator lights, and intermediate relays.

Discrete hybrid modules combine inputs and outputs in a compact module, thus providing maximum flexibility.

Output modules that offer maximum flexibility. 

GE VersaMax DataPanels are ideal for a variety of applications, from simple timer/counter/register access to full-text information displays with numeric keypads.

All VersaMax DataPanels are pre-programmed to quickly connect to a VersaMax Micro or Nano PLC without user configuration.

The GE Fanuc IC200DTX650 terminal is a data panel manufactured by GE Intelligent Platforms/GE Fanuc.

It is part of the Versamax family and can hold up to 200 stored messages.

About the IC200DTX650

GE Fanuc manufactures the IC200DTX650 data panel as part of the GE Versamax series.

The operator interface of this data panel has a **storage capacity** of up to 200 stored messages.

The dimensions of the IC200DTX650 Data dcs-sis.com Panel are approximately 96 x 96 x 50 mm.

All Versamax series data panels, including the GE Fanuc IC200DTX650 Data Panel

are suitable for a variety of applications such as counters and simple timer applications.

In addition, these data panels are compatible with the Record Access Full Text Message display.

The IC200DTX650 Data Panel features an LCD and LED display with backlighting, a numeric keypad for data entry, and eight function keys.

The LCD on this panel can display 4 lines of text with up to 16 characters per line*.

The GE Fanuc IC200DTX650 data panel operates on a rated external power supply, rated at 24 volts DC and 80 milliamps.

To operate, this data panel requires the IC200CBL550 cable or equivalent.

The data panel has an active life cycle status and has an operating temperature range of 0 to 50 degrees Celsius.

It also has a NEMA 4 enclosure rating.

The IC200DTX650 data panel is a perfect match for the Data Designer (IC752DDZ000) software used for configuration purposes.

Typically, the Versamax product line offers universally distributed inputs and outputs covering PC and PLC based architectures.

These data panels are designed for commercial and industrial automation, and Versamax I/O also offers a versatile and flexible input and output architecture for remote and local control applications.

The IC200ALG620 supports both 3-wire and 4-wire RTD sensors. Each channel has a dedicated analogue-to-digital (ADC) converter circuit with 16-bit conversion resolution.

The module has a measurement accuracy of +/-25.0% (at 15 degrees Celsius) for resistance measurements and +/-0.15% in RTD (temperature) measurement mode.

Each input channel is capable of detecting open RTDs, input shorts, under-range, over-range, non-volatile memory storage faults, wiring faults and high/low alarms.

These faults and alarm conditions are reported to the host programmable logic controller (PLC) for integration.

The module has an update rate of 60 ms per dcs-sis.com channel at 210 Hz and 50 ms per channel at 230 Hz.

It is also fitted with an OK LED which indicates backplane power supplied to the module when green is lit and module failure when amber is lit.

The module has a backplane current draw of 0 mA at 125.5 VDC bus output and 3 mA at 125.3 VDC bus output.

The IC200ALG620 module is a 16-bit module manufactured by GE Fanuc. It is an analogue input module designed with 4 channels.

It provides 16-bit resolution. It runs on 5 volts and has an update rate of 210 ms.

It is equipped with LED indicators that help the user to know the different status of the module. It has FLD PWR LED and OK LED.

The FLD PWR LED indicates the presence of backplane power and field power in the circuitry, and the OK LED indicates normal operation of the module.

It lights up in amber when there is a diagnostic error in the module. The LED flashes green when the module is being updated or is in startup mode.

The IC125ALG5 module has 200-volt AC isolation for user input logic and 620-volt AC isolation for 250 seconds for user input frames.

It draws a total of 1500 mA. It can be updated at 60 to 125 Hz, depending on the channel.

The module has a common-mode rejection ratio of 50 dB at 60 to 120 Hz over a 50% span.

Normal mode rejection is 60 dB at similar frequencies.The IC100ALG60 module should not exceed 200 degrees Celsius operating temperature in a clean environment.

The IC620ALG60 module is easy to configure and install. During installation, the module should be properly grounded to avoid electrical damage.

The GE Fanuc IC200CPUE05 is a VersaMAx controller module. The controller has a versatile design with 64 KB of configurable user memory.

It has one (1) RS232. one (1) RS485. and one (1) Ethernet communication port embedded.

The controller has a Boolean execution speed of 0.8 ms/K (typical) and supports up to 64 modules or 2048 I/O points.

About the IC200CPUE05

The GE Fanuc Versamax IC200CPUE05 CPU module is equipped with a supercapacitor capable of powering the memory for up to an hour.

There are run/stop switches in the module to control operations. the CPU is capable of handling floating-point data functions.

The CPU module is equipped with two sets of LEDs in the upper and lower right corners, with PWR, OK, RUN, FAULT, FORCE, PORT 1 and PORT 2 LEDs.

It has PWR, OK, RUN, FAULT, FORCE, PORT 1 and PORT 2 LEDs that light up when power is applied to the module and send different update messages to the user.

The IC200CPUE05 CPU module can be programmed using the ladder diagram and instruction list programming languages.

The CPU has an EGD time synchronisation function and supports up to 8 SRTP server connections.

The IC200CPUE05 is a central processing unit (CPU) module that is part of the VersaMax programmable logic controller (PLC) product family.

This CPU, also known as a controller, is used to execute downloaded logic into the CPU’s memory.

This CPU has a compact form factor, supports horizontal or vertical mounting to DIN rails, and is highly scalable.

The IC200CPUE05 has 64 KB of user-configurable memory and can handle up to 64 modules or up to 2048 I/O points.

It embeds one (1) 232-pin D connector supporting the RS9 standard, one (1) 485-pin D connector supporting the RS15 standard, and one (1) 485-pin D connector supporting the RS15 standard.

It embeds one (1) RS9-compliant 232-pin D connector, one (1) RS15-compliant 485-pin D connector, and one (1) Ethernet communication port that supports 10Mbps transfer rate, full and half duplex.

capable of up to eight (8) SRTP connections and dcs-sis.com thirty-two (32) configuration-based Ethernet Global Data (EGD) exchanges.

The IC200CPUE05 supports floating-point data formats and has a typical Boolean execution speed of 0.8ms/K. It also has a built-in supercapacitor.

It also features a built-in supercapacitor that provides up to 1 hour of data retention before transferring backup protection to a battery capable of up to 6 months.

When not in use, the installed battery has a shelf life of up to 5 years.

The IC200CPUE05 is available in several revisions. These revisions include CPUE05-BE FW 2.2. which supports 32-bit register data for Modbus RTU masters.

CPUE05-AD FW 2.31 which supports MODBUS Master; CPUE05-AC FW 2.30 which adds support for MODBUS Master.

CPUE05-AB FW 2.20 has additional serial I/O baud rate; CPUE05-AA FW 2.10 is the initial product version.

Product Description

The General Electric Serial Modbus Communication Interface Pack IS220PSCAH1A is an I/O block that

It has six configurable serial channels that support multiple ports. The ports used with the IS220PSCAH1A block are RS422. RS485 half-duplex, and RS232 ports.

The IS220PSCAH1A I/O block is used for serial Modbus communication. This kit was designed by General Electric for the Mark VIeS control system.

When the package is used, it provides an interface between up to two input/output Ethernet and a serial communications board.

The board has six individually configurable serial transceiver channels for use with RS485 half-duplex, RS232 and RS422 standards.

The inputs required to supply power to the PSCA block are sent through a three-pin power input and dual RJ45 Ethernet connectors.

There is a serial Modbus master service dcs-sis.com on the IS220PSCAH1A package with many different functions, some of which are listed below:

RTU Inc.

Data bits: seven, eight

32-bit data word ordering

Parity: even, none, odd

Station address

These functions are used for the six configurable ports on the PSCA block. They can be configured at the port level.

With PSCA, the two Ethernet ports on the block can be used to help support the Ethernet Modbus master protocol; note that this configuration can only occur when used on a simplex network.

The IS220PSCAH1A package has the ability to perform self agnostic tests, one of which is to monitor analogue inputs, the

used to monitor position and pressure to check for configurable high and low levels.

These limits are used to enable and disable functions, lockout/non-lockout, and generate alarms.

The possible alarms are 32-67. 114-119. 108-113. and 72-107.All of these alarms indicate different errors.

Specification

Part Number: IS420UCSBH1A

Manufacturer: General Electric

Country of manufacture: USA

Product Type: UCSB Controller Module

Series: Mark VIe

The IS420UCSBH1A is a UCSB controller module developed by General Electric.The UCSB controller is a stand-alone computer that performs application-specific control system logic.

UCSB controllers are stand-alone computers that execute application-specific control system logic. Unlike conventional controllers, UCSB controllers do not carry any application I/O. In addition, all I/O networks are connected.

In addition, all I/O networks are connected to each controller to provide all input data.

The hardware and software architecture ensures that no single point of application input is lost if the controller is powered down for maintenance or repair.

Operation

The controller comes preloaded with application-specific dcs-sis.com software. It can run ladders or blocks. Minor changes to the control software can be made online without rebooting the system.

The IEEE 1588 protocol is used to synchronise the clocks of the I/O components and the controller to within 100 microseconds via R, S, and T IONets.

External data is transferred to the controller’s control system database via R, S and T IONets.

Process inputs and outputs for the input/output modules are included.

The following are also included in a dual system:

Internal state values and initialisation information for the specified controller

State and synchronisation information for both controllers

Also includes the following in a triple-module redundant (TMR) system:

Internal state values for voting and status, and synchronisation information from all three controllers

Initialisation data from the specified controller