Category: TEWS

Technical Information

 Conduction Cooled single-width 32 bit PMC module

conforming to IEEE P1386.1

 PCI 2.1 compliant master/slave interface

 3.3V and 5V PCI Signaling Voltage

 Board size: 143.75 mm x 74 mm

 Four high speed asynchronous/synchronous (HDLC)

serial interfaces

 Support of RxD, TxD, RxC, TxC, RTS, CTS, CD and

GND on rear connector P14

 Physical interface (individually programmable per

channel):

EIA-232. EIA-422. EIA-449. EIA-530. EIA-530A, V.35.

V.36 and X.21

 Maximum data rate: 10 Mbit/s (synchronous),

2 Mbit/s (asynchronous), internally or externally

provided clock

 EIA-232: up to 115.2 kbit/s

Temperature range: -40°C to +85°C

A 14.7456 MHz oscillator provides standard asynchronous

baud rates. An additional 24 MHz oscillator is provided for

other baud rates. A 10 MHz oscillator is used for the

synchronous baud rate of 10 Mbit/s.

Each channel also provides various interrupt sources,

generated on INTA. The interrupt sources can be enabled

or disabled individually.

Multiprotocol transceivers are used for the line interface.

The physical interface is selectable by software, individually

for each channel as EIA-232. EIA-422. EIA-449. EIA-530.

EIA-530A, V.35. V.36 or X.21.

The following signals are provided by the TPMC363  for

each channel at the front and rear-I/O connectors:

Receive Data (RxD +/-), Transmit Data (TxD +/-), Receive

Clock (RxC +/-), Transmit Clock (TxC +/-), Ready-To-Send

(RTS +/-), Clear-To-Send (CTS +/-), Carrier-Detect (CD +/

) and GND.

The TPMC363 provides rear panel I/O via P14.

Software Support (TDRV009-SW-xx) for different operating

systems is available.

Application Information

The TPMC363 is a conduction cooled single-width 32 bit

PMC with four high speed serial data communication

channels.

The TPMC363 is the successor of the discontinued

TPMC362. providing similar functionality and full connector

and pin-out compatibility.

The serial communication controller is implemented in

FPGA logic, along with the bus master capable PCI

interface, guaranteeing long term availability and having the

option to implement additional functions in the future.

Each channel provides dedicated receive and transmit

FIFOs for high data throughput.

Data transfer on the PCI bus is handled via TPMC363

initiated DMA cycles with minimum host/CPU intervention.

Several serial communication protocols are supported by

each channel, such as asynchronous, isochronous,

synchronous and HDLC mode.

Technical Information

 Standard single-width 32 bit PMC module conforming

to IEEE P1386.1

 Board size: 143.75 mm x 74 mm

 PCI 3.0 compatible interface

 3.3V and 5V PCI Signaling Voltage

 64 or 32 interrupt generating bit I/O lines

 64 TTL I/Os or 32 differential EIA-485 or M-LVDS I/Os

 Direction individually programmable per line

 TTL signaling voltage (maximum current: +/24mA)

 ESD and overvoltage protection for each TTL I/O line

 ESD protected EIA-485 & M-LVDS transceiver

 64 TTL I/O lines or 32 differential I/O lines on rear

connector P14 (upper 8 lines changeable to system ground)

 Operating temperature -40°C to +85°C

MTBF (MIL-HDBK217F/FN2 GB 20°C)

TPMC321-10R: 350 000 h

TPMC321-11R: 891 000 h

TPMC321-12R: 846 000 h

Application Information

The TPMC321 is a conduction cooled single-width 32 bit

PMC module offering 64 ESD-protected 5V-tolerant TTL

lines or 32 differential I/O lines using ESD-protected EIA

422 / EIA-485 compatible line transceivers or Multipoint

LVDS transceivers.

Each line is individually programmable as input, output or

tri-state. The receivers are always enabled, which allows

determining the state of each I/O line at any time. This can

be used as read back function for lines configured as

outputs. Each TTL I/O line has a pull-up resistor. The pull

up voltage is selectable to be either +3.3V or +5V.

Differential I/O lines are terminated, EIA-422 / EIA-485

lines with 120 Ω, M-LVDS lines with 100 Ω.

Each input can generate an interrupt. Signal edge

handling is programmable to interrupt on rising and/or

falling edge of an input signal. Interrupts can be enabled

and disabled for each bit. For interrupt source detection

the status of each bit can be read from interrupt status registers.

The TPMC321 provides rear I/O via P14.

Software Support (TDRV006-SW-xx) for different

operating systems is available.

Application Information

The TPMC310 is a conduction cooled single-width 32 bit

PMC module providing two channel of high speed CAN

bus interface.

The PLX PCI9030 PCI Target Chip is used for the PCI interface.

Two Philips SJA1000 CAN controllers (CAN specification

2.0B supported) are used for the two CAN bus channels.

The CAN bus I/O interface provides two independent

channels, isolated from system logic and from each other.

CAN High Speed transceivers are used for the CAN bus

I/O interface. An on board termination option (solder pads)

is provided for each CAN bus channel allowing to

configure on board termination and pass through mode for

the CAN bus.

The TPMC310 uses the P14 I/O connector for the CAN

bus I/O interface.

Software support (TDRV010-SW-xx) for different operating

systems is available.

Technical Information

CAN High Speed transceivers are used for the CAN bus

I/O interface. An on board termination option (solder pads)

is provided for each CAN bus channel allowing to

configure on board termination and pass through mode for

the CAN bus.

The TPMC310 uses the P14 I/O connector for the CAN

bus I/O interface.

Software support (TDRV010-SW-xx) for different operating

systems is available.

 Conduction Cooled single-width 32 bit PMC module

conforming to IEEE P1386.1

 PCI 2.1 compliant interface

 3.3V and 5V PCI Signaling Voltage

 Board size: 144 mm x 74 mm

 CAN Bus Interface

• Two channel High Speed CAN interface

• Two Philips SJA1000 CAN controller

• Supports CAN specification 2.0B

• I/O interface based on TJA1050 transceiver,

channels isolated from system logic and from each other

• On board termination option for each CAN bus channel

 Operating temperature range –40°C to +85°C

Technical Information

Asynchronous and Variable Time Triggered Synchronous

Operation Modes are supported.

Wheel speed sensor support covers two- and three

current levels sensors, sensors with additional status

information and the “AK-protocol”.

All TPMC160 signals are accessible through a HD50

SCSI-2 type front I/O connector.

Software Support (TPMC160-SW-xx) for different

operating systems is available.

 Standard single-width 32 bit PMC module conforming

to IEEE P1386.1

 Board size: 149 mm x 74 mm

 PCI 3.0 compliant interface

 5 V and 3.3 V PCI /O signaling interface

 HD50 SCSI type I/O connector mounted in front panel

 8 channels, configurable as PSI5 or Wheel Speed

Sensor simulation

 PSI5 supports -P/-U/-D/-A/-V communication modes,

125 and 189 kbps transmission rates

 Wheel speed sensor supports 2- and 3-level sensors

and VDA/AK-Protocol

 Current sinks with three adjustable levels

 Custom protocol option available

 Operating temperature -40°C to +85°C

 MTBF (MIL-HDBK217F/FN2 GB 20°C)

TPMC160-10R: 369000 h

Application Information

The TPMC160 is a standard single-width 32 bit PMC

module and supports a 33 MHz / 32-bit universal (5 V / 3.3

V) PCI interface.

The TPMC160 offers eight isolated automotive sensor

simulator channels, which can act as a PSI5 or as wheel

speed sensor. The sensor simulation supports a current

sink with three adjustable levels. It also features PSI5

Sync and Reset pulse detection. The sensor simulation

channels are isolated against the system and against each other.

PSI5 support includes PSI5-P, -U and -D bus topologies

and both 125 kbps and 189 kbps transmission rates.

Asynchronous and Variable Time Triggered Synchronous

Operation Modes are supported.

Wheel speed sensor support covers two- and three

current levels sensors, sensors with additional status

information and the “AK-protocol”.

Technical Information

Form Factor: Standard single-width 32-bitPMC

module conforming to IEEE Std 1386/1386.1

Board size: 149 mm x 74 mm

PCI 3.0 compliant interface

5 V and 3.3 V PCI /O signaling interface

4 Resolver or LVDT/RVDT-to-digital convert channels

Angle with 16-bit resolution

0-12 VRMS programmable sensor inputer

0-12 VRMS, 1-20 kHz programmable excitation

Tracking rate up to ¼ excitation frequency

Digital velocity value

Synchro channels:

0-28 VRMS programmable sensor input

external excitationup to 28 VRMS, 4 0 0 H z –20 kHz

50-pin MDR type I/O connector mounted in front panel

Operating temperature -40°C to +85°C

MTBF (MIL-HDBK217F/FN2 GB 2 0 °C )

TPMC151-10R: 682 000 h

TPMC151-20R: 463 000 h