Category: TEWS

The FB2200 flow computer measures and controls oil

and gas flow for up to two meter runs. The FB2200

supports gas differential pressure, gas linear meters,

and liquid linear meters.With a rugged housing and

multiple I/O, communications, and power options, the

FB2200 provides accurate and reliable flow

measurement in the harshest conditions.

The FB2200 is part of Emerson’s new field mount flow

computer family that delivers a convenient approach

to remote oil and gas sites by addressing challenges to

power, safety, measurement reliability, and accuracy.

Designed for simplified configuration and ease of use,

the FB2200 is also highly configurable and supports

flow and fluid property calculations right out of the

box. The flexible design provides exactly what is

required for each application. The FB2200 can also be

equipped with FBxWifi™ functionality allowing you to

configure and retrieve site data more safely than before.

The new flow computers also come with the latest

Rosemount™ sensor technology, providing high

accuracy differential pressure and static pressure

measurement with long term stability to help improve

measurement confidence and production efficiency.

Application Information

The TPMC377 is a conduction cooled single-width 32 bit

PMC module offering 4 channels of high performance

RS232/RS422/RS485 programmable asynchronous serial

interface with P14 I/O. Each of the four channels are

isolated from the system and against each other by digital

isolator and on board integrated DC/DC converter.

The serial channels can be individually programmed to

operate as RS232. RS422 or RS485 full duplex / half

duplex interface. In addition programmable termination is

provided for the RS422/RS485 interfaces. After power-up

all serial I/O lines are in a high impedance state.

Each RS232 channel supports RxD, TxD, RTS, CTS and

GND. RS422 and RS485 full duplex support a four wire

interface (RX+, RX-, TX+, TX-) plus ground (GND). RS485

half duplex supports a two wire interface (DX+, DX-) plus

ground (GND).

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422/RS485 channels.

The UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC377 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D154 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interface

 Quad UART: Exar XR17D154

 Programmable Interfaces:

 RS232

 RS422

 RS485 full duplex

 RS485 half duplex

 Programmable Termination for RS422/RS485

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422/RS485 FD channel; D+/- and GND for each

RS485 HD channel.

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422/RS485: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV)

 Operating temperature -40°C to +85°C

Application Information

The TPMC376 is a conduction cooled single-width 32 bit

PMC module offering 4 channels of high performance

RS232/RS422/RS485 programmable asynchronous serial

interface with P14 I/O.

The serial channels can be individually programmed to

operate as RS232. RS422 or RS485 full duplex / half

duplex interface. In addition programmable termination is

provided for the RS422/RS485 interfaces. After power-up

all serial I/O lines are in a high impedance state.

Each RS232 channel supports RxD, TxD, RTS, CTS and

GND. RS422 and RS485 full duplex support a four wire

interface (RX+, RX-, TX+, TX-) plus ground (GND). RS485

half duplex supports a two wire interface (DX+, DX-) plus

ground (GND).

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422/RS485 channels.

The UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC376 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D158 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interface

 Octal UART: Exar XR17D158

 Programmable Interfaces:

 RS232

 RS422

 RS485 full duplex

 RS485 half duplex

 Programmable Termination for RS422/RS485

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422/RS485 FD channel; D+/- and GND for each

RS485 HD channel.

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422/RS485: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV )

 Operating temperature -40°C to +85°C

Application Information

The TPMC375 is a conduction cooled single-width 32 bit

PMC module offering 8 channels of high performance

RS232/RS422/RS485 programmable asynchronous serial

interface with P14 I/O.

The serial channels can be individually programmed to

operate as RS232. RS422 or RS485 full duplex/half

duplex interface. In addition programmable termination is

provided for the RS422/RS485 interfaces. After power-up

all serial I/O lines are in a high impedance state.

Each RS232 channel supports RxD, TxD, RTS, CTS and

GND. RS422 and RS485 full duplex support a four wire

interface (RX+, RX-, TX+, TX-) plus ground (GND). RS485

half duplex supports a two wire interface (DX+, DX-) plus

ground (GND).

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422/RS485 channels.

The UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC375 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D154 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interface

 Quad UART: Exar XR17D154

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422 channel. One channel offers extended support

(full modem or RTS+/- and CTS+/-)

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV)

 Operating temperature -40°C to +85°C

Application Information

The TPMC372 is a conduction cooled single-width 32 bit

PMC module and offers 4 channels of high performance

asynchronous serial interface.

Three different standard modules are available: The

TPMC372-10xR provides 4 RS232 interfaces. The

TPMC372-11xR provides 4 RS422 interfaces. The

TPMC372-12xR provides 2 RS232 and 2 RS422 interfaces.

Other configurations are available as factory build option

on a per channel base.

All modules offer P14 I/O. Each RS232 channel supports

RxD, TxD, RTS, CTS and GND. Each RS422 channel

supports RxD+/-, TxD+/- and GND. One channel of the

TPMC372-10xR/-12xR offers full modem support (TxD,

RxD, CTS, RTS, DSR, DTR, CD, RI and GND) for RS232.

One channel of the TPMC372-11xR supports RxD+/-,

TxD+/-, RTS+/-, CTS+/- and GND for RS422.

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422 channels. The

UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC372 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D158 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interfaces

 Octal UART: Exar XR17D158

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422 channel. Two channels offer extended support

(full modem or RTS+/- and CTS+/-)

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV )

 Operating temperature -40°C to +85°C

Application Information

The TPMC371 is a conduction cooled single-width 32 bit

PMC module and offers 8 channels of high performance

asynchronous serial interface.

Three different standard modules are available: The

TPMC371-10xR provides 8 RS232 interfaces. The

TPMC371-11xR provides 8 RS422 interfaces. The

TPMC371-12xR provides 4 RS232 and 4 RS422 interfaces.

Other configurations are available as factory build option

on a per channel base.

All modules offer P14 I/O. Each RS232 channel supports

RxD, TxD, RTS, CTS and GND. Each RS422 channel

supports RxD+/-, TxD+/- and GND. Two channels of the

TPMC371-10xR/-12xR offer full modem support (TxD,

RxD, CTS, RTS, DSR, DTR, CD, RI and GND) for RS232.

Two channels of the TPMC371-11xR support RxD+/-,

TxD+/-, RTS+/-, CTS+/- and GND for RS422.

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422 channels. The

UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC371 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.