Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0

Category: Industry Trends

Home / Industry Trends (Page 293)
April 29, 2025 BY
IN A-B

A-B 1402-LS51 Power Monitoring Line Synchronisation Module

Phase rotation mismatch fault (3-phase sync mode only); No reference bus voltage fault; No sync bus voltage fault; Reference bus overvoltage fault and Sync bus overvoltage fault.

The module’s energy meter functions include a large number of measurable and calculable parameters, in particular current (amperes, per phase and neutral); average current (amperes); positive sequence current (amperes); and

Negative Sequence Current (Amps); Current Unbalance Percentage Voltage (Volts, per phase L-L, also L-N in 4-wire systems).

Average voltage (Volts, L-L, also L-N in four-wire systems); Positive-sequence voltage in Volts; Negative-sequence voltage in Volts; Percentage voltage unbalance.

Frequency in Hertz; phase rotation (ABC, ACB); power factor in per cent (total power factor, also per phase in four-wire systems).

Watts (total watts and watts per phase in a four-wire system); Volt-amperes (total volt-amperes and volt-amperes per phase in a four-wire system).

Varistors (total number of varistors and number of varistors per phase in a four-wire system); Power consumption in kWh.

reactive power consumption in kilovolt-amperes-hours; and demand (amperes, volt-amperes, and watts).

The 1402-LS51 module is a line synchronisation module manufactured by Allen-Bradley/Rockwell Automation.

The Allen-Bradley 1402-LS51 Line Synchronisation Module is a solid-state module, not a hard-wired electromechanical module, which means it is suitable for a variety of industrial applications.

However, it should not be used for safety functions that require sudden surges of power, such as emergency stops.

Attempting to use this solid-state module for dcs-sis.com emergency functions may damage the module, cause it to fail, prevent the emergency or error it was designed to respond to, or cause injury to the user.

The purpose of the Allen-Bradley 1402-LS51 Line Synchronisation Module is to synchronise two different three-phase systems through features such as load sharing, automatic synchronisation, and high-speed power system monitoring.
April 29, 2025 BY
IN A-B

A-B 1398-DDM-075 Servo Drive Unit Ultra 200 Servo Drive

Description

The Allen-Bradley 1398-DDM-075 is an Ultra 200 series digital servo drive: The Allen-Bradley 1398-DDM-075 is an Ultra 200 series digital servo drive. The servo drive is enabled when the AC input voltage requirement is 100-240VAC rms, single-phase or three-phase, and the input frequency is 47-63 Hz. The drive has peak output currents of 50 amps (single phase input) and 75 amps (three phase input) and continuous output currents of 15 amps (single phase input) and 35 amps (three phase input). Peak output power is 14 kilowatts for single phase, 20 kilowatts for three-phase peak output, and 7.5 kilowatts for three-phase continuous output.

About the 1398-DDM-075

The Allen-Bradley 1398-DDM-075 is an Ultra 200 servo drive. This drive was one of Allen-Bradley’s early servo drive products. It is a microprocessor-based servo drive with built-in functions for managing drive current, speed, and position.Ultra 200 servo drives dcs-sis.com (such as the 1398-DDM-075) are compatible with brushless servo motors.

Specifically, the 1398-DDM-075 has an AC input voltage requirement of 100-240VAC rms, single-phase or three-phase, and an input frequency of 47-63 Hz. It also has an auxiliary input that is isolated from the supply voltage of the main AC input circuit. The auxiliary AC input is rated at 100-240 VAC, single phase, 47-63 Hz, and has an input current of 1.0 amp for 100 VAC and 0.5 amp for 240 VAC.
April 29, 2025 BY
IN A-B

A-B 1715-OB8DE 1715 Redundant I/O Module 8-Point Digital Output Module

About the 1715-OB8DE

The 1715-OB8DE, manufactured by Allen-Bradley, is a redundant I/O module that is part of the Allen-Bradley Redundant I/O Module 1715 series.

The 1795-OB8DE has a maximum power dissipation of 3 watts. 1715-OB8DE operates at temperatures as low as -25 degrees Celsius and as high as 70 degrees Celsius.

The redundant l/O module is described as an 8-point digital output module with 18 to 16 AWG wire gauge. the unit has a shipping weight of approximately 290 grams.

The 1715-OB8DE is a chassis-based application with DIN rail mounting.

The 1715-OB8DE has an open housing type with a display system that serves as a dashboard for health and status indication of the module.

The 1715-OB8DE has an output signal of 18 to 32 volts DC.The shipping dimensions of the 1715-OB8DE are 1 5/8 inches long, 4 5/8 inches wide, and 6 1/2 inches high.

According to the manufacturer, the 1715-OB8DE is equipped with 18-16 AWG solid core stranded copper wire rated at less than 2 watts.

The 1715-OB8DE has a vibration resistance of 2 grams and a dcs-sis.com shock resistance of 25 grams on DIN rail and in operating condition.

The module has a shock resistance of 30 grams in the non-operating condition and when mounted on a DIN rail, and 50 grams when not mounted.

The 1715-OB8DE is available with current source output type and surge transient immunity.
April 28, 2025 BY
IN A-B

A-B 2711-K10G1 PanelView Standard Operator Interface Terminal


Allen-Bradley’s 2711-K10G1 is part of the Panelview 1000 series and is designed for users to efficiently connect to machines.

Operators can easily enter information and commands through the keypad. There is a clear 10.1-inch greyscale display.

greyscale display. Each module is housed in a durable NEMA 12/13 or 4X type enclosure and uses 85-264 VAC input power.

A printer (RS-232) port and remote I/O port are available for adaptive communications.

The Allen-Bradley 2711-K10G1 PanelView Standard Operator Interface Terminals are the high standard in control system automation.

They are hard at work around the world supporting the automotive, food and beverage, pulp and paper, water and wastewater treatment, and petrochemical industries.

Each 2711-K10G1 standard terminal is UL, cUL/CSA, and CE listed.

They are rated for NEMA 4X (IP54. IP65) and approved for Class 1 Division 2 (flat panel only) operation.

These terminals are designed and engineered for scalability, reliability and compatibility to reduce cost of ownership and increase productivity.

This 2711-K10G1 device displays critical alarm data and records and displays important data that triggers an alarm.

When an alarm is recognised, the operator is notified to troubleshoot the problem.

The 2711-K10G1 supports up to five languages in a single application, switching between English, French, Italian, German, and Spanish text in run mode without the need for an ATA memory card.
April 28, 2025 BY
IN Motorola

Motorola MVME5500 Single Board Computers

The MVME5500 series is designed to meet the needs of OEMs, including those in the defence, aerospace, industrial automation and transportation sectors.

Customers who need to maintain backward compatibility with their existing VMEbus infrastructure while updating the technology for their applications can upgrade to the MVME5500 Series and take advantage of its enhanced performance features.

Backward compatibility

The MVME5500 continues the direction SMART EC has taken since the MVME5100 series, which is to provide a migration path from SMART EC’s embedded controllers and single board computers (SBCs) to a single platform.

This migration path enables OEMs to support different I/O requirements using the same base platform, simplifying part number maintenance, expertise requirements and resource sharing.

The MVME5500 series provides customers with dcs-sis.com a migration path from the MVME2300. MVME2400. MVME2600. MVME2700 and MVME5100 boards.

They can take advantage of features such as the MPC7455 processor, Gigabit Ethernet and dual independent 33/66 MHz PMC stations.

Transition Module

The MVME761 Transition Module provides industry-standard connector access to IEEE 1284 parallel, 10BaseT or 100BaseT ports via RJ-45 connectors.

The MVME761 Transition Module provides industry standard connector access to IEEE 1284 parallel, 10BaseT or 100BaseT ports via RJ-45 connectors, asynchronous serial ports configured as EIA-574 DTEs via two DB-9 connectors, and synchronous/synchronous serial ports via two HD-26 connectors.

These serial ports are labelled Serial 3 and Serial 4 on the MVME761 panel.

These serial ports are labelled as Serial 3 and Serial 4 on the MVME761 panel and can be individually configured as EIA-232. DCE or DTE by the user by installing a SMART EC Serial Interface Module (SIM).

The P2 adapter board provides the interface signals for the MVME761 transition module.

There are two separate P2 adapter boards: one for 3-row backplanes and one for 5-row backplanes.

The 3-row P2 adapter board provides connectivity for 8-bit SCSI. The 5-row P2 adapter board supports 16-bit SCSI and PMC I/O.
April 28, 2025 BY
IN Hitachi

Hitachi 500LTD01 Isolated Line Transformer

Applications

The line transformer 500LTD01 is designed for FSK channels in the 50 Bd to 2400 Bd range.

It is used to isolate and protect the RTU500 series modems 23WT23. 23WT25 and 560FSM10 from remote control lines.

In addition, it can be connected to other data terminal equipment.

It is optimised for wire-first communication with a frequency range of 300 Hz to 3400 Hz and a line impedance of 600 ohms for the above modems.

All three types of modems allow high-resistance interleaving on lines such as party lines and multisplit lines.

This is because the line transformer has no additional load on the line.

In configurations using full duplex communication channels, two line transformers are required, one for the transmit direction and the other for the receive direction.

Features

The line transformers can withstand isolation voltages of:

> 10 kV, 50 Hz, 10 sec.
April 28, 2025 BY
IN Motorola

Motorola MVME2400 Series VME Processor Module

The MVME2400 series VME boards offer the performance of Motor ola’s PowerPlus II architecture and can be fully customised to meet the needs of

your applications requiring two PCI mezzanine cards (PMCs). Flexibility

The MVME2400 provides an excellent base platform that can be quickly

and easily customised for a variety of industry-specific applications.

Utilising Motorola’s low-power, high-performance PowerPC750 microprocessor, the Peripheral Component Interconnect (PCI) bus for onboard

peripherals, processor/memory bus to PCI bus bridges and VME interfaces, the

The MVME2400 processor module packages optimal levels of flexibility and performance into a single VME slot

IEEE P1386.1-compliant PMC slot The MVME2400 features dual PMC ports supporting

front panel and P2 I/O. The following are P2 I/O based PMCs

PMC committee recommendations for PCI I/O when using the

VME64 expansion connector will be compatible with pin-outs

MVME2400 in addition to providing high performance expansion I/Os

IEEE P1386.1 compliant PMC ports form a common architecture for future generations.

Simply replacing the PMC meets changing I/O needs while reusing the same base platform, reducing long-term cost ownership.
April 28, 2025 BY
IN A-B

A-B 6155R-14SXPH Standard Model Non-Monitor Computer


The Allen-Bradley 6155R-14SXPH is a VersaView 1400R standard non-display C-Series industrial computer with 14 slots.

Specifically, it has 2 half-length ISA slots and 3 PCI slots, as well as 3 full-length ISA slots, 4 PCI slots, and an internal CompactFlash connector.

The computer’s ports include 1 parallel printer port, 2 serial COM ports, and 1 10/100 RJ45 Ethernet port,

1 USB 1.1 port, 1 PS/2 port for keyboard or mouse, and 1 VGA port.

It also has an audio port, a 3.5-inch floppy drive and a CD drive.

It has a 2 GHz Intel Pentium 4 Celeron processor and 256 MB of RAM.

It is expandable up to 2 GB of memory, consisting of two DIMMS with 1 GB of memory. The computer requires an external monitor.

It has an auto range AC input voltage of 90-264V AC, a line frequency of 47-63 Hz, and power consumption of 150V or 1.5 A @ 100V RMS and 0.63 A @ 240V RMS.

Operating temperatures are 0-50 °C and non-operating temperatures are -20-60 °C. The computer can also withstand 15 g of heat. The computer can also withstand operating shocks of 15 g and non-operating shocks of 30 g (both 11 ms ½ sine waves), and 1 Grms of random operating vibration.

and 1 Grms of random operating vibration. The computer’s enclosure is rated NEMA Type 1.

Technical Description of the 6155R-14SXPH

VersaView Non-Display Series Terminal with 2 GB of RAM and 80 GB of hard drive storage with 120-240V AC or 9-36V DC input power.
April 28, 2025 BY
IN GE

Fanuc IC200ALG331 4-Point Analogue Voltage/Current Input Module

The module can also be used to relay analogue signals, which may be the result of continuous calculations within the logic of a programmable logic controller (PLC).

displayed by panel meters and recorded by data loggers. It can also be used to interface with a signal isolator or signal splitter, to

or to cascade a reference signal to another single-loop controller or PLC for more complex controller architectures, such as cascade control.

The IC200ALG331 has output channels that can be configured via software to generate +/-10 VDC or 4-20 mA output signals.

Each channel has a maximum update rate of 7ms and an accuracy of +/-0.1% of full scale maximum.

Each channel is also capable of configuring and detecting high/low limits, over/under ranges, open circuits, loss of field power, non-volatile memory faults, and

as well as individually assigning output behaviour for PLC stop or module errors (such as holding the last state or dropping to zero (0)), which can also be modified.

Since the IC200ALG331 is fully software configurable, there is no need to install a terminal jumper to the module to set the operating mode.

The GE IC200ALG331 module is a 16-bit analogue output module. It is equipped with 4 isolated channels.

It is part of the GE Fanuc Versamax module family. The main function of the module is to control multiple analogue devices at once.

The module can be easily configured using only software. There are no jumpers or switches in this output module variant.

The operating voltage range of this module is between -10 and 10 volts DC. The current rating of the module is 4 to 20 mA.

The analogue output module updates itself in a 7 millisecond time period. It draws a total of 15 milliamps of current from the 5-volt bus.
April 28, 2025 BY
IN GE

IC200MDL930 8-Point Relay Output Module for VersaMax I/O Series

The IC200MDL930 contact output is essentially a dry contact output. It requires an external supply voltage source to conduct the proper voltage to the connected electrical load.

It can be used for resistive or conductive loads, but it is recommended that conductive loads, external protection or suppression circuits (such as fuses) be installed.

Output contacts are rated at a minimum of 10mA per point; 2.0A for 5 to 265 VAC, max; 2.0A at 5 to 30 VDC, 0.2A at 31 to 125 VDC, max.

All current ratings are resistive load ratings. In addition, the nominal external supply voltage ratings for the contact outputs are 5/24/125 VDC and 120/240 VAC.

The IC200MDL930 has a maximum backplane current consumption of 245 mA when all outputs are energised.

The module is equipped with a separate channel indicator to describe the energised state of each output channel.

It also has a separate module OK LED indicator to indicate the active power received by the module from the backplane power supply.

The IC200MDL930 module is an 8-point output module manufactured by GE Fanuc. It is part of the Versamax family.

The output points of the module are individually isolated. The output module draws 245 mA of power from the baseboard with all outputs active.

The IC200MDL930 module is fully compatible with AC and DC loads. Each of the module’s eight points has its own LED indicating field power through those points.

The module contacts are closed by default during module activation. At this time the output bit is set to 1. The module is easy to install when using the rack mounting method on a baseboard.

The output module is certified to CE, cULus and other industry standards. It is used for global settings.

The IC200MDL930 output module is an intelligent device that performs faster processing than other similar modules.

This output module has no output leakage current. Each point relay is designed with a fixed coil and an armature.

Menu

Search for products

Back to Top
Product has been added to your cart