Welcome to the official website of CNIACS Automation Technology Co., Ltd!

Emerson A6740 / A6740-10 16-Channel Output Relay Module

The 16-channel output relay module is designed for high reliability of the plant’s most critical rotating machinery.

This 2-slot monitor is used with the AMS 6500 to form a complete API 670 machinery protection monitor.

Applications include steam, gas, compressor and hydraulic turbine machinery.

Any channel clear, alarm or warning signal can be selected as an input to the 16 channel output relay module.

Uses Boolean logic, applies time delays and selects output relays

Easy-to-use software provides a graphical logic display that graphically guides the user through the configuration.

The AMS 6500 Machinery Health Monitor is an integral part of PlantWeb® and AMS software.

PlantWeb provides comprehensive machinery health operation in conjunction with the Ovation® and DeltaV™ process control systems.

AMS software provides maintenance personnel with advanced predictive and performance diagnostic tools, enabling them to determine machine failures early with confidence and accuracy.

3U-sized 2-slot plug-in module reduces cabinet space requirements by half compared to traditional 6U cards

API 670 compliant, hot-swappable modules

60 inputs, 30 logic expressions, 16 relay outputs

6740 is a 12TE wide module for IMR6000 series racks

6740-10 is a 10TE wide module for IMR6500 dcs-sis.com series racks

Data Outputs

Relays

Configurable redundant relays Data Outputs

Configurable redundant relays

Mechanical relays, API 670 compliant

Specifications Control Voltage: 13-32

VDC Contact Load: 48 V, 1 A Normally open or normally closed, selectable

Normally open or normally closed, selectable

Normally open or normally closed, selectable

Single Pole Double Throw (SPDT), Optional

Emerson 00813-0100-0112 VersaMax Modular Input/Outputs and Controls

Rich and Useful I/O Options

Emerson offers a wide range of discrete, analogue, hybrid, and dedicated I/O modules. These modules can be freely combined

These modules can be freely combined to create stand-alone I/O stations with up to 256 I/O points and extended I/O systems with up to 2048 I/O points.

The perfect match for today’s open systems

VersaMax gives you the freedom to connect via PROFINET (remote I/O only), Modbus/TCP, other Ethernet networks as well as Genius, DeviceNet,

Profibus-DP, etc. VersaMax gives you the freedom dcs-sis.com to connect to a wide range of host controllers, including PLCs, DCSs, and PC-based control systems.

VersaMax also fully supports the power and open architecture of Emerson’s PC-based control solutions.

Cost-Effective Control and I/O

VersaMax features intuitive diagnostics, module hot-swapping, and quick-connect wiring to extend uptime and

Reduce engineering and training requirements and significantly lower project lifecycle costs.

Designed to Maximise Ease of Use

Every aspect of VersaMax has been carefully refined to meet the needs of the user. Snap-on I/O carriers mean no tools are required for module installation or removal.

Convenient rotary switches can be used to set bus addresses, reducing programming time. With VersaMax, you can even address I/O automatically.

Easy troubleshooting and machine setup

You can easily configure VersaMax I/O using the integrated PAC Machine Edition (PME) software.

PME is the same software as all PACSystems CPUs, so you only need one tool for everything from small to large applications.

This approach utilises the same hardware configuration, network configuration and programming editor. In addition, the QuickPanel+ HMI’s single tag database simplifies HMI development.

Emerson 00813-0100-0161 Compact Programmable Automation Controller

PACSystems™ RSTi-EP CPE200 Series

Compact Programmable Automation Controllers

Everything you need today to meet the business challenges of tomorrow.

The RSTi-EP CPE200 Compact Controller Series, with its built-in safety design, open programming and open communications, simplifies connectivity to traditional sensors and actuators as well as external analytical software platforms.

Simplifies connectivity to legacy sensors and actuators, as well as external analytical software platforms, while reducing cost and complexity for OEMs and end users.

The compact controller family simplifies connectivity to traditional sensors and actuators, as well as external analytical software platforms, while reducing cost and complexity for OEMs and end users.

Featuring the same high-performance runtime and toolchain as the PACSystems™ RX3i large-format controller, this compact controller family

It provides large programmable logic controller (PLC) functionality in a smaller footprint.

The PACSystems™ RX3i is designed to provide the functionality of a large programmable logic controller (PLC) in a small footprint, yet be small, cost-effective, and IIoT-ready so machine builders don’t have to sacrifice productivity or performance.

Out-of-the-box cybersecurity

Industrial controls have always been a target for cyber threats. We understand the risks involved in protecting our customers’ most important assets.

We believe in defence-in-depth architecture to secure assets from potential cyber threats.

The RSTi-EP CPE200 Compact Controller Series is Achilles Level 2 certified and has been designed with technologies such as Trusted Platform Modules and Secure Boot to ensure security.

Technologies such as platform modules and secure boot to prevent malicious applications and ‘unauthorised’ operating systems.

Centralised configuration allows encrypted firmware updates to be performed from a secure central location. an extensive set of network security technologies and tools help prevent unauthorised updates.

while built-in secure communication protocols help prevent man-in-the-middle and denial-of-service attacks.

Emerson 00813-0100-0115 RXi – Industrial Monitor

Modularity and flexibility

The RXi – Industrial Monitor Display Portfolio is available in screen sizes ranging from 7 inches to 24 inches, all in widescreen format.

The 7-inch and 15-inch models also feature outdoor sunlight readable (SLR) screens.

The modular nature of the unit provides great flexibility in configuring RXi – Industrial Monitors.

You can easily replace an indoor screen with an outdoor screen, change the screen size, or replace a damaged screen, all while using the same backplane module.

Recognising that effective processes require proper visualisation, the RXi – Industrial Monitor portfolio offers more functionality than ever before.

With display port inputs and display port outputs on every industrial monitor, you can simplify your architecture with MST daisy chaining.

Designed for Visualisation

RXi – Industrial monitors are designed with precision in mind when it comes to visualisation.

Multi-touch, projected capacitive screens feature high resolution, vivid graphics capabilities and fast response times to ensure relevant information is always available for viewing and interaction.

This enables operators to make faster, more informed decisions with a high-performance platform that reduces total cost of ownership.

Anywhere, anytime: a wide range of applications

The portfolio operates efficiently in temperatures as high as 65°C and as low as -20°C. The modules can be used outdoors and are available in a variety of configurations. Modules can be used outdoors and are equipped with sunlight-readable (SLR)

Readable (SLR) UV-protected screens.The screens of the RXi – Industrial Monitors are strictly IP66 certified and are protected against dust, humidity and even direct water spray.

RXi – Industrial monitors offer you solutions to meet your every need.

Display technology: designed to maximise the user experience

RXi – Industrial Displays bring industrial displays into today’s connected world, combining design, durability and power.

In an ultra-thin package, it’s perfect for the factory floor.

The sleek and powerful user experience (UX) connects people to machines with the latest touchscreen technology and widescreen displays.

The capacitive ultra-touch screen can be used while wearing personal protective equipment and is as sensitive as the latest smartphones.

In addition, the outdoor-grade sunlight readable (SLR) screen is almost twice as bright as the brightest smart devices.

Optically bonded screens with UV protection greatly reduce reflections and glare, providing operators with vivid, clear images for more complete and powerful process visualisation.

Emerson Rosemount 3153N Nuclear Qualified Pressure Transmitter

Rosemount 3153N Nuclear Qualified Pressure Transmitter

Industry-leading performance

– Meets the following standards

o IEEE Std 323™-1974/1983/2003

o IEEE Std 344™-1975/1987/2004

– 36 Mrad (360 kGy) TID Gamma Radiation

– 8.5g ZPA Seismic

– 333ºF (167.2ºC) Vapour/Temperature

– 0.2% Reference Accuracy

Introduction to the Rosemount 3153N Nuclear Pressure

The Rosemount 3153N Nuclear Pressure Transmitter is designed for precision pressure measurement in nuclear applications.

These applications require reliable performance and safety over a long service life.

The 3153N complies with IEEE Std 323™-1974/1983/2003 and IEEE Std 344™-1975/1987/2004.

Irradiance is 36 Mrads TID Gamma, Seismic Rating 8.5g ZPA, and Vapour Pressure/Temperature Performance.

Rigorous quality control during manufacturing includes traceability of pressure retaining components, special nuclear cleaning and hydrostatic pressure testing.

Transmitter Description

The Rosemount 3153N transmitter is similar in construction and performance to the proven Rosemount 3051 transmitter.

The transmitter is available in absolute (AP), gauge (GP), and differential (DP) configurations with a choice of six pressure ranges.

Direct electronic sensing using a fully sealed coplanar capacitive sensing element (see Figure 1) eliminates mechanical force transfer and problems associated with shock and vibration.

Compact design, two-wire system compatibility, and non-interactive external range and zero adjustments for standard calibration simplify installation and commissioning.

Wiring terminals and electronics are located in separate compartments, helping to

ensure that the electronics remain sealed during installation.

Emerson A6210 Monitor

A6210 Thrust Position, Differential Expansion and Rod Position Monitor for AMS 6500 Machinery Health Monitor

The A6210 monitor has 3 different operating modes: thrust position, differential expansion or rod position.

The thrust position mode precisely monitors the thrust position and reliably protects the machine by comparing the measured axial position with the alarm position.

Reliably provides machine protection by comparing the measured axial position with the alarm setpoint.

Setpoints – drive alarms and relay outputs, thus reliably providing protection for the machine.

Axial thrust monitoring is one of the most critical measurements on turbomachinery.

Sudden and small axial movements should be detected within 40 milliseconds or less to minimise or avoid rotor-to-casing contact.

or avoid rotor-to-case contact. Redundant sensors and voting logic are recommended.

Thrust bearing temperature measurement is strongly recommended as a supplement to thrust position monitoring.

Shaft thrust monitoring consists of one to three displacement sensors mounted on the shaft end or thrust collar in the axial direction parallel to the shaft.

The displacement sensors are non-contact sensors that measure shaft position.

For critically important safety applications, the A6250 monitor provides triple redundant thrust protection.

The A6210 monitor can also be configured for differential expansion measurement.

During turbine start-up, both the casing and the rotor expand due to changes in thermal conditions.

Differential expansion therefore measures the relative difference between the displacement sensor mounted on the housing and the target of the sensor mounted on the shaft. If

housing and shaft grow at approximately the same dcs-sis.com rate, the differential expansion remains ideally close to zero.

Differential expansion measurement modes are supported in series/complementary or cone/slope modes.

Finally, the A6210 monitor can be configured in average rod drop mode to monitor riding belt wear in reciprocating compressors.

Over time, the rider band in a horizontal reciprocating compressor wears due to the force of gravity acting on the horizontally orientated piston in the compressor cylinder.

If the rider belt wears beyond the point where the piston would come into contact with the cylinder wall, damage to the machine and possible malfunction occurs.

By installing at least one displacement probe to measure the piston rod position, you will be notified when the piston drops – a sign of a worn rider band.

You can then set the shutdown protection threshold for automatic tripping.

Emerson CSI A6120 Enclosure Seismic Vibration Monitor

CSI A6120 Enclosure Seismic Vibration Monitor for CSI 6500 Machinery Health Monitor

The Case Seismic Vibration Monitor for use with electromechanical seismic sensors is designed for high reliability on the plant’s most critical rotating machinery.

This 1-slot monitor is used in conjunction with other CSI 6500 monitors to form a complete API 670 machinery protection monitor.

Applications include steam, gas, compressors and hydraulic turbines. Casing measurements are common in nuclear power applications.

The primary function of the casing seismic vibration monitor is to accurately monitor casing seismic vibration, the

and to reliably protect machinery by comparing vibration parameters with alarm set points, actuated alarms and relays.

A case seismic vibration sensor, sometimes referred to as a case absolute vibration sensor (not to be confused with a shaft absolute vibration sensor), is an electrodynamic, internally spring-loaded, and magnetically actuated vibration sensor.

It is an electrodynamic, internal spring and magnet, velocity output type sensor.

A housing seismic vibration monitor monitors the overall vibration of a bearing housing at millimetres per second (inches per second).

Since the sensor is mounted on the bearing housing, vibration in the housing can be affected by many different sources.

These include rotor motion, foundation and bearing box stiffness, blade vibration, adjacent machinery, etc.

When replacing ffeld sensors, many are being updated to piezoelectric sensors, which provide internal integration from acceleration to velocity.

Piezoelectric sensors are a new type of electronic sensor rather than the older electromechanical type.

Case Seismic Vibration Monitors are backward compatible with electromechanical sensors installed in the ffeld.

The CSI 6500 Machinery Health Monitor is an integral part of PlantWeb® and the AMS Suite.

PlantWeb combines Ovation® and DeltaV™ process control systems to provide operators with an integrated view of machinery health.

The AMS Suite provides maintenance personnel with advanced predictive and performance diagnostic tools to accurately determine machine failures at an early stage.

Features:

Dual-channel, 3U-sized, 1-slot plug-in module that cuts cabinet space requirements in half compared to traditional four-channel 6U cards

API 670-compliant hot-swappable modules

Remotely selectable limit multiplication and trip bypass

Pre- and post-buffered and proportional outputs, 0/4-20 mA outputs, 0 – 10 V outputs

Use with electric (electromechanical) sensors 9266. 9267. or 9268

Sensor Inputs

Number of inputs: two independent channels

Input Type: Electro-mechanical, Differential

Emerson sensor inputs: Part No. 9266. 9267. or 9268

Isolation: Galvanically isolated from power supply

Input resistance: >100 kΩ

Input voltage range: – 5 – +15 VDC

Input frequency range:

Lower cut-off frequency 1 or 5 Hz

Upper cut-off frequency 50 – 2000 Hz adjustable

Emerson M-Series DC to DC System Power Supplies

About DeltaV™ System Power Supplies

Power supplies – systems can’t operate without them.DeltaV™ System Power Supplies provide you with the most efficient and reliable power solutions available.

DeltaV power supply kits provide power to the system electronics and to the field. This is all the power you need for your DeltaV system.

Benefits

DC/DC system power supplies are plug-and-play components. They fit any power carrier, including horizontal 2-width and vertical 4-width carriers.

These carriers contain an internal power bus that connects to the controller and I/O interfaces, eliminating the need for external wiring. The carriers are easily mounted on T-shaped DIN rails!

Flexible and cost-effective, DeltaV DC/DC system power dcs-sis.com supplies accept 12V DC and 24V DC input power.

Modular construction and load-sharing capabilities of the power supplies allow you to add more power to your system or provide power redundancy.

Safety. Your I/O is always accurate because I/O subsystems and controllers are always supplied with stable, accurate 12V DC or 5V DC power. Power supplies are EMC- and CSA-compliant; notification is immediate in the event of a power failure; and system and field power supplies are completely isolated.

Simplified system power supply. System power supplies provide more current on the 12 VDC I/O interface power bus, eliminating the need for 24 to 12 VDC bulk power supplies. All controller and I/O power is now available from the factory 24 VDC bulk power supply.

Emerson DeltaV Distributed Control System MX Controller

INTRODUCTION

The MX controller provides communication and control between ffeld devices and other nodes on the control network. Control strategies and system configurations created on earlier DeltaV™ systems can be used in this powerful controller.The MX controller has all the features and functionality of the MD Plus controller, but twice the capacity.

The control language implemented in the controller is described in the Control Software Suite product data sheet.

Advantages

Right-Sized Controller

The MX controllers complement the MQ controllers by providing a larger capacity controller for applications requiring greater control capability:

2 X control capacity

2 X user configurable memory

2 X DST counts

DeltaV™ MX controllers and DeltaV I/O subsystems are easy and quick to install.

Post change. You can easily upgrade an dcs-sis.com MQ controller to an MX to handle project scope changes later in the project The MX has the same installed footprint as an MQ controller, but twice the performance. Simply replace the MQ with the MX, and then

All existing configurations, documentation, and hardware design remain intact.

Redundant Architecture: MX controllers support 1:1 redundancy for increased availability. Existing MD/MD Plus or MQ controllers are upgradable and powerful online!

Emerson Ovation™ I/O Input/Output Modules

Introduction 

Emerson’s Ovation™ control technology is designed to support long-term process reliability and expandability.  

With modular plug-in components, Ovation I/O delivers embedded advanced control applications with built-in fault tolerance and system diagnostics. 

With their inherent flexibility, Ovation I/O modules convert input signals and create output signals, performing a multitude of functions. Specialized I/O modules are also available. 

Simplified Maintenance 

Standardized assembly style simplifies maintenance and reduces spare parts inventory costs. 

Single-point DIN rail fastening makes installation and configuration quick and easy. Built-in connectors eliminate power and communications wiring. 

Ovation I/O modules are software configurable, therefore no jumpers or thumb wheels are necessary. Their advanced electronics also deliver low power consumption.

Features 

▪ Modular, plug-in components support long-term process reliability 

▪ Modules are installed and configured quickly and easily with single-point DIN rail fastening 

▪ Built-in connectors eliminate power and communications wiring 

▪ Electronic ID identifies module type, group, serial number and revision 

▪ Fewer module styles reduce spare parts inventory costs 

▪ Redundant power supplies deliver system reliability 

▪ “Hot swapping” streamlines system maintenance 

▪ Standardized status indicators offer color-coded diagnostic messages 

▪ Remote Ovation I/O provides a flexible, costeffective means to dcs-sis.com distribute I/O modules to strategic locations throughout the plant 

Ovation I/O Architecture 

The Base 

Ovation packaging reduces the system footprint by using base units which attach to mounting plates by DIN rail; these hold four independent Ovation I/O modules of any style. This approach simplifies maintenance by making it easy to install, move or replace individual base units. 

Base unit features include:  

▪ Field terminal blocks that accept two 14 AWG or a single 12 AWG 

▪ I/O bus communications built into the base 

▪ I/O modules automatically addressed by location 

▪ I/O modules may reside in any location 

▪ I/O module redundant power distribution 

▪ No interconnecting cables for I/O bases 

▪ Built-in spare fuse holders and strip gauge in base 

Search for products

Back to Top
Product has been added to your cart