Category: Industry Trends

Product Description

The DS200AAHAG1AD is an ARCNET connector board manufactured by General Electric as part of the Mark V LM SpeedtronicTurbine control system.

Mark V LM manual GEH-6353B clearly summarizes the function of the DS200AAHAG1AD in the control system. The board is referred to by its acronym AAHA.

The DS200AAHAG1AD, abbreviated AAHA, is part of the Speedtronic Mark V LM control panel.

The board is capable of providing connectivity and interface functionality between a control engine with an I/O core and external hardware.

The control engine is typically located within the core. The kernel typically requires the use of two AAHA boards.

One board is used to facilitate the stage link between the user interface and the core.

The second board is capable of connecting the core to COREBUS.

This link allows communication between the I/O core and the control engine.

The DS200AAHAG1AD is plugged in and installed to operate without any type of hardware or software modification.

The AAHA board is relatively small. It has an EBNC connection port that is not normally used.

It has one ARCBNC-B labeled P1 and one ARCBNC-A port labeled P1.

These ports are BNC ARCNET communication ports. There is an E2 and E1 LED indicator.

There is an EPL 9-pin connection that is not normally used and an APL 10-pin connection port that is used as an ARCNET communications link.

The expansion base uses a box connector. It supports output voltages in the range of 0 to 125 volts DC with nominal voltages of 5. 24. and 125 volts DC.

For the voltage range of 8 to 5 volts AC, this expansion base has a load current of 265 amps per point.

The IC200CHS212 chassis is constructed of high quality materials.The Versamax module provides high performance and is a cost-effective industrial solution.

The expansion relay has ports for connection to programmers and handheld devices.

It is designed with open architecture and should be protected from dust, dirt and contaminants. The temperature of the module should not exceed 60 degrees Celsius.

The IC200CHS212 is GE’s 16-point I/O relay expansion base. The relay is replaceable, labeled 8 amps and fused.

The VersaMax I/O Modules IC200MDL740 and MDL750 provide 24 VDC O.5A outputs to control the IC200CHS212 relays.

The IC200CHS212 dimensions (excluding DIN rail height) are 253.7 mm (9.9 in.) x 126 mm (4.95 in.) x 73 mm (2.8 in.).

Power supply modules such as the IC200CHS212 snap onto all Versamax interface units or power booster carriers.

Any power supply can be specified as the main power supply for modules in an I/O station or as an additional power supply for large I/O applications.

The IC200CHS212 and other VersaMax I/O plug-in disconnect bases enable the IC200CHS003 to connect to a variety of termination bases.

Relay bases provide more protection and higher current output. The relays are controlled by the outputs of the VersaMax I/O modules.

Users can easily disconnect each point signal from the I/O module by disconnecting the base. The module’s field terminals can also be removed.

The relays located on the plug-in terminals are intended to be controlled using a typical 24 VDC 0.5 VersaMax output module.

IC200CHS212 Technical Description

The GE IC200CHS212 base is a 16-point expansion base. It provides LED indicators for each I/O point.

The IC200ALG432 module is an analog module with mixed inputs. It is manufactured by GE Fanuc as a Versamax module.

About the IC200ALG432

The GE Fanuc IC200ALG432 module is a hybrid analog module that runs on a 10-volt DC power supply.

It is a 12-bit module equipped with 4 channels and 2 output channels.

The analog module has an update rate time of 0.4 milliseconds and an input response time of 5 milliseconds.

The analog module requires an external power supply to power the outputs. The inputs of the module are powered by the external power supply of the transceiver.

The CPU is present in the module that handles the operation. the IC200ALG432 module has LEDs on the front of the module that indicate the flow of power and backplane currents.

No thermal derating occurs in this hybrid module. the IC200ALG432 module draws a total of 160 milliamps of current during normal operation. including load current.

The diagnostic feature of the module helps to detect the loss of power on the user side.

It provides four channels and two channel outputs. The outputs require a 24V external power supply and the inputs are powered from the transceiver’s external power supply.

The CPU or NIU performs intelligent processing of the IC200ALG432 module. Includes 4 words of analog input data and 2 words of analog output data.

This IC200ALG432 uses LEDs to indicate the presence of user-side power for analog field-side circuits as well as backplane power.

The LEDs emit a green light when operating as intended. When properly installed, this module reports the loss of user-side power failure for field-side circuits and conveniently sets up jumpers for outputs.

The IC200ALG432 can be set to maintain the last state or default values even if the backplane or field power is temporarily interrupted. The module reports the loss of user-side power failures for field-side circuits.

About IC200DTX850

The IC200DTX850 terminal is a data display terminal manufactured by GE Intelligent Platforms/GE Fanuc for the GE Versamax product line.

These Versamax series data terminals, including the GE Fanuc IC200DTX850 terminal, are specifically designed for use in a variety of applications that

Including simple timer and counter applications, they can also display full text messages.

These terminals can be controlled by the user via a numeric keypad. Connecting a Versamax Nano or Micro PLC to the terminals is easy and requires no user configuration.

Because these Versamax terminals are pre-programmed, the GE Fanuc IC200DTX850 Operator Interface Terminal specifically supports up to 200 stored messages.

The GE Fanuc IC200DTX850 Data Display Terminal also has an LCD backlight for the screen.

It has a keypad with 8 keys for control functions and requires the IC200BL555 cable or equivalent to support its operator interface.

The data panel operates on an external power supply rated at 24 volts DC and 50 milliamps.

The GE Fanuc Versamax IC200DTX850 data display terminal measures approximately 182 x 101 x 37 mm.

It has an operating temperature range of 0 to 50 degrees Celsius.

The IC200DTX850 data interface terminal has an RS-232 serial port for communication purposes.

This port is designed for different commands, including serial input/output commands, Modbus RTU slave commands or SNP slave commands.

In addition, this data terminal is compatible with the Data Designer software.

The Versamax controllers compatible with this terminal are available in micro and nano models, which are small in size, while offering powerful control and a high level of performance.