Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0

Category: Industry Trends

Home / Industry Trends (Page 169)
March 24, 2025 BY
IN GE

139-H-FLC Full Load Current Output Option Relay

The 139-H-FLC relay can be supplied with ground fault current and it will accept all current carrying conductors through the ground fault current window.

Please note that it is highly recommended that at least two current leads need to be wound together to minimize noise pickup on the relay.

There is a specially designed current that can be used to dcs-sis.com help output lower level signals.

Frequently Asked Questions about the 139-H-FLC

What is the memory capability of the 139-H-FLC multi-wire general purpose motor protection relay?

This 139-H-FLC is designed to electronically record up to 30 minutes of memory to simulate heat buildup in a motor.

If no overload occurs during this 30 minute period, the memory will be refreshed.

However, if an overload occurs or the motor starts, the circuitry remembers these conditions and can reduce the amount of time available for future overload conditions.

If the motor enters a trip condition due to overheating, the relay will latch to restart for at least 30 minutes to allow the motor to cool.

Motor start trip conditions and overload conditions may cause the motor to heat up, hence the 30 minute lockout time.

Blocked-Rapid Trip, Short Circuit, Unbalance, or Ground Fault conditions do not cause heating and enable the turntable to perform an immediate system reset.

Can users customize the 139-H-FLC Multi-Wire Universal Motor Protection Relay for specific motors?

Users can select from 15 different operating profiles for the 139-H-FLC Multi-Wire Universal Motor Protection Relay.

Four switches are used to select the desired operating profile. The user can find the manufacturer’s data for the motor

Plot the data on the run curve to customize the 139-H-FLC to the motor that needs to be protected.

The full load current from terminals one and two on this model will be proportional to the percentage of full motor current.

Current levels will not be affected by any different wiring lengths.
March 24, 2025 BY
IN ABB

ABB Ability Symphony Plus Distributed Control System (DCS)

The new SDe series continues to innovate to address one of the biggest challenges facing control system owners: upgrading existing infrastructure without disrupting operations.

By preserving field wiring, terminal units and modular wiring, SDe solutions

Helping plant owners protect process controllers, I/O modules and automation technology as it evolves

their Symphony Harmony and INFI 90 investments while dcs-sis.com process controllers, I/O modules and automation technology evolve, enabling progressive growth with minimal impact.

The SDe I/O family includes a range of intelligent analogue, HART, digital and hybrid I/O modules with redundancy that

can communicate with higher-level controllers via the local bus.

Each module is supplied with an evolved mounting base for Harmony Rack systems and is fully compatible with HR BRC410 and SD controllers.

The SDe Series I/O product line includes digital and analogue modules for horizontal or vertical DIN rail mounting and integration with intelligent field devices and protocols.

Hardwired I/O and fieldbus I/O co-exist, using the same library of function blocks to build real-time control applications.

Legacy SDe series analogue input modules interface with field inputs.

such as pressure and flow transmitter signals, thermocouple inputs, and resistance temperature device (RTD) inputs.

Analogue output modules provide output signals to regulate final control elements such as control valves, positioners, actuators and more.

The input channels of the SDe Series digital input modules read the status of switches, relay contacts, solenoids, etc. The digital output modules are available in DC or DC output versions.

Digital output modules provide output channels for DC or AC switching applications.

The digital outputs can be used to drive alarms and bistatic final control elements such as actuators, relays, and solenoids.

For SDe Series digital I/O, each channel can be individually configured as an SOE (sequence of events) point.

This flexibility eliminates the cost and complexity of assigning additional digital inputs as SOEs in the field.

Whether the I/O is locally or remotely located, SOEs with 1 ms time stamps can be used throughout the system.

The SDe family of ruggedised control and I/O products dcs-sis.com provides seamless interconnectivity with intelligent field and electrical equipment and more advanced applications.

Extreme operating temperature ranges and scalable architectures are offered in a compact modular space.

In addition, the series features sustainability improvements, such as reduced power consumption and the use of standards-based technology, which reduces the total cost of ownership for plant owners.

The main principle behind the SDe range is to develop, enhance and extend ABB’s existing INFI 90. Harmony and Symphony DIN (SD) systems.

These systems are currently installed at more than 7.000 sites worldwide.

For Harmony rack mounting, the SDe Series offers increased modularity, enhanced functionality, one-to-one module replacement and space-appropriate mounting options to ensure seamless growth.

Fully compatible with the SD Series, it supports the expansion of SD systems with the latest technology and I/O hardware and software, delivering increased performance, reliability and capacity.
March 21, 2025 BY
IN Woodward

Woodward CPC-DX Redundant Skid Mounted Current Pressure Converter

Manual isolation valves are included in the package, allowing the user to easily repair or replace each individual current-to-pressure converter.

Both automatic and manual transfer logic is available for this skid block assembly, depending on the design of the system.

The skid block’s automatic transfer logic simplifies system design because it does not require external relay/switching logic to operate.

This minimises wiring at the converter-to-converter and control-to-converter interfaces.

The CPC’s configurable alarm/shutdown logic allows the user to easily configure which system conditions force an automatic transfer from the master CPC to the slave CPC.

The manual transfer feature is also available for systems where the user wishes to switch between pressure converters via external logic or manual switching.

The master select discrete input is used to allow the user to dcs-sis.com easily and quickly select the desired control CPC.

An integrated oil pressure gauge allows the user to visualise which converter is in control and verify the skid’s output oil collector pressure level.

Discrete output relay contacts can also be connected to system indications (lights, lamps, plant DCS) to assist in system operating condition monitoring.

Features:

Anti-fouling .

. No small passages to block .

.111 N (25 lb) rotary chip shear .

. Self-cleaning valve design

Automatic and manual switching

Fast changeover time

. Minimised system disturbances

Precise pressure control

Increased reliability

. High Pressure Signal Selection Design

. In-line Repairable

. Master/Slave Logic

Includes isolation valves

Protected with padlock

Large pressure gauge

Remote master/slave indication

Compact size

Available in 10 and 25 bar models

Division 2 and Zone 2 Hazardous Location Approved
March 21, 2025 BY
IN Reliance

Reliance WR-D4008 Programmable Logic Controller

Product Description.

The Reliance Electric PSC7000 WR-D4008 PLC module is an advanced programmable logic controller designed to streamline industrial processes.

It offers superior control features, robust performance and seamless integration with existing automation systems.

The module is a reliable solution for industries seeking an efficient and cost-effective automation solution.

Features

1. High-speed processing: The PLC module has a powerful processor for high-speed data processing and fast response times.

2. Expandable I/O capacity: With its expandable I/O capacity, the module can accommodate a variety of input and output devices for flexible system configuration.

3. User-friendly interface: The module features an intuitive and user-friendly interface that simplifies programming, monitoring and troubleshooting tasks.

4. Powerful Communication Capabilities: Supports a variety of communication protocols for seamless integration with other devices and systems.

5. Enhanced Security: The PLC module integrates powerful security features to protect sensitive data and prevent unauthorised access.

Applications

Reliance Electric PSC7000 WR-D4008 PLC modules are used in a wide range of industrial applications, including:

1. Manufacturing: Optimise production processes, monitor equipment performance and ensure precise control of key parameters.

2. Energy: the module helps to manage power distribution, monitor energy consumption and control renewable energy systems.

3. Oil & Gas: Facilitates remote monitoring and control of pipelines, storage tanks and drilling equipment to improve operational efficiency and safety.

4. Water treatment: The PLC module assists in the automation dcs-sis.com of water treatment plants to ensure precise control and efficient operation.

5. Transport: It can effectively control and monitor traffic systems, railway networks and airport infrastructure.

Technical Specifications

The technical specifications of Reliance Electric PSC7000 WR-D4008 PLC module are as follows:

1. Processor: Advanced 32-bit processor with 100 MHz clock speed.

2. Memory: 256 KB RAM and 2 MB flash memory for programme storage.

3. I/O capacity: Up to 4096 digital I/O points and 128 analogue I/O points.

4. Communication ports: Multiple serial and Ethernet ports for seamless connectivity.

5. Operating temperature: -10°C to 60°C (14°F to 140°F) for reliable performance in a variety of environments.
March 21, 2025 BY
IN Woodward

Woodward APECS™ 0175 Engine Linear Actuator

Description

APECS™ 0175 linear actuators deliver precise positioning and form the foundation of a full electronic governing system. 

Many of the moving parts normally associated with electric actuators dcs-sis.com are eliminated, prolonging the MTBF (mean time between failure). 

The actuator design employs the principle of variable reluctance for consistent force over the entire stroke. 

This simple design of a proportional electric linear actuator utilizes a linear armature whose magnetic force is proportional to the input current to the coil. 

These actuators are easy to install by mounting near the fuel system with a direct connection to the fuel control rod or level. 

In most installations, the normal rotary-torotary connection is eliminated, resulting in a more trouble-free and accurate control system. 

APECS 0175 actuators are suitable for installation on diesel, gasoline, or natural gas engines with fuel system force requirements of less than 4.0 pounds (17.8 N) of force. 

Woodward also manufactures 0175 actuators integral to the engine block or fuel pump. 
March 21, 2025 BY
IN ABB

ABB EMB01S-XIO Evolution Module Base

The EMB01S-EMR Evolution Module Base mounts an AI12e, AO02e, DI06e, or DO01e I/O module to the EMC-_B0x Evolution Mounting Base.

or DO01e I/O modules to the EMC-_B0x Evolution mounting base.

The base connects the I/O module to the HN800 I/O bus and connects the I/O cable to the field terminal.

The chassis supports all functions of the AI12e, AO02e, DI06e, or DO01e I/O modules. This includes optional module redundancy.

Features and Benefits

Mounts AI12e, AO02e, DI06e, or DO01e I/O modules to the EMC-_B0x Evolution mounting base

Connecting I/O modules to the redundant HN800 I/O bus

Connect I/O module to NTDI0x TU via NKTU01 cable

Connect I/O module to NIDI01 TM via NKTU02 or NKTM01 cable

General information

Article number 7PAA005096R1 (EMB01S-XIO)

Lifecycle status active

Line redundancy yes

Channel 14. 15 or 16

Hot Swap No

Supported IO modules AI12e, AO02e, DI06e, DO01e

Single or redundant Single

Form Factor EMC-_B0_ Evolution Mounting Chassis

Mounting EMC-DB01. EMC-DB02. EMC-SB01. EMC-SB02

HN800 Bus length 190 mm

MTBF (per MIL-HDBK-217-FN2) PR E: 245.577 hours @ 30˚C, 244.473 hours @ 40˚C, 240.272 hours @ 70˚C

MTTR (hours) 8 hours

Power overvoltage category 1. Tested according dcs-sis.com to IEC/EN 61010-1

Process Signal Connections Thirteen (13) total: 4-AI, 2-AO, 3-DI, 4-DO

Field power connections @ I/O terminals (TU or TM)

Field power fuse @ I/O terminals (TU or TM)

Signal connection Terminable block on NTDI0x, NIDI01 or HDIOT-XIO-01

Maximum current 250 mA

Galvanic isolation test voltage 1500 V for up to 1 minute
March 21, 2025 BY
IN Emerson

Emerson DeltaV™ VerticalPlus Input/Output Subsystem Carrier

Functional features:

Designed for SIS

Modular design for flexible installation

Allows for online expansion

Increased I/O density

I/O density for cabinet-mounted systems

Introduction to the DeltaV™ VerticalPlus I/O Rack

Keep your I/O subsystems running efficiently with DeltaV™ VerticalPlus I/O Racks.

The VerticalPlus platform allows you to integrate DeltaV SIS logic solvers vertically, giving you the flexibility you need for cabinet design.

Power supplies/controllers and I/O carriers are modular.

You buy only what you need, but rest assured that as your dcs-sis.com system grows, you can add plug-and-play carriers-it’s easy!

The Advantage

Designed specifically for SIS. The redesigned carrier supports simplex and redundant SLS modules.

These modules communicate via a redundant safety bus, which is separate from the BPCS communications.

The VerticalPlus carrier also communicates with other SIS nodes on the vertical and horizontal carriers via redundant SISNet repeaters.

The modular design allows for flexible installation. A single T-shaped DIN rail is all that is needed to mount the power/controller carrier in place.

Fieldbus power is now independent for each individual card.

The modular design approach of the DeltaV system allows you to add I/O carriers as needed.

Allows you to expand online. Additional carriers can be added online as needed.

Increases the density of the cabinet-mounted system. Six I/O carriers can be mounted on one side of a standard 1200mm x 600mm x 2200mm cabinet.
March 21, 2025 BY
IN Foxboro

FOXBORO IDP10 I/A Series® Electronic Differential Pressure Transmitter

The Foxboro® brand Model IDP10 is an analogue output, two-wire d/p Cell® transmitter.

It provides accurate, reliable differential pressure measurement and transmits a 4 to 20 mA analogue output signal.

High Reliability and Value

 is available in conventional or low-profile construction.

 Excellent performance and long-term stability based on microprocessor technology.

 Industry-standard 316L ss, Co-Ni-Cr, nickel alloy(1), monel alloy, or tantalum sensor materials, depending on transmitter construction.

 Available in durable aluminium or 316 SS housings; both meet NEMA 4X and IP66 ratings.

 Optional mounting bracket kits are available for duct, surface, or manifold mounting of the transmitter.

 Dual seal certified to ANSI/ISA 12.27.01-2003.

 CE marked; complies with applicable EMC, ATEX, and PED European directives.

 Designed for hazardous area installations. Versions are available to meet organisational explosion-proofing and zoning requirements.

 Standard 5-year warranty.

Affordable Smart Transmitter Features

When you need the flexibility and performance of a configurable dcs-sis.com smart transmitter, but don’t need a digital output signal, these transmitters offer excellent benefits at a very affordable price:

 Liquid crystal display (LCD) digital indicator with on-board pushbuttons

 Pushbutton configuration and calibration

– Linear or square root output

– Adjustable damping

– Forward or reverse output

– Fail-safe outputs; scale up or scale down

– Rearrange without applying pressure

 can be easily upgraded to a fully intelligent version (FoxCom™, HART® or FOUNDATION™ fieldbus)

I/A SERIES PRESSURE TRANSMITTERS The I/A Series pressure transmitter family includes d/p Cell, Gauge, Absolute, Multi-Range, Multi-Variable, and High Performance transmitters, as well as pressure seals with remote or direct connection.

and transmitters with remote or directly connected pressure seals, all featuring field-proven silicon strain gauge sensors and universal topside construction.
March 21, 2025 BY
IN ABB

ABB REF 542plus Multifunctional Protection and Switching Controls

Configuration

Each protection and control application can be easily configured via the software function module, which allows the following functions to be arbitrarily defined as part of the secondary system:

LEDs for local indication (meaning and colour)

Single line diagrams showing the status of switching devices

Protection programme

Control programmes

Interlocking programmes

Automation sequences

All functions of the switchboard can be specified in co-operation dcs-sis.com with ABB. The configuration results are saved and delivered to the user together with the switchboard.

By using the “Function Block” programming language (FUPLA), the REF542plus multifunctional protection and switchboard control unit provides engineers, in

especially non-software specialists, the opportunity to easily update switchboard operation and handling.

With the REF542plus, users can fully integrate secondary systems into a true programmable controller.

This flexibility is very favourable for defining control functions for automation sequences.

This can include, for example, interlocking of switchgear, preventing the release of specific protective functions and initiating switching sequences.

The REF542plus multifunction unit offers a wide range of logic functions so that the various required control schemes can be configured.

The required control schemes are configured. The range of logic functions includes

AND logic gates

NAND logic gates

OR logic gates

NOR gates

XOR gates

Bistable and Monostable Flip-Flops

Bistable and Monostable Flip-Flops

Timers

Pulse Generator

Memory

Similar to the free definition of control schemes, each required protection scheme can be configured by combining the available protection function modules.

For example, the following protection functions are available:

Timed overcurrent protection

Inverse time overcurrent protection

Directional overcurrent protection

Undervoltage or overvoltage protection

Distance protection

Transformer and motor differential protection

Cable, transformer and motor thermal protection

Reverse power protection

Synchronisation check
March 21, 2025 BY
IN Emerson

Emerson AMS 6500 Protection Monitor Configuration

Pre-configured user-selectable measurement types simplify software configuration

Password protection with 4 user login levels and customisable access rights

Context-sensitive help information to quickly resolve set-up issues

Includes trending, time functions, order analyses and start/stop data for comprehensive setup.

Configuration includes setup of basic predictive functions, including troubleshooting and diagnostics

Applications

The AMS 6500 Configuration Software for Machinery Protection allows you to configure protection modules, view real-time vibration monitoring systems and sensor health.

The intuitive configuration process begins with the selection of the card type. Next, the configuration software displays a simple table view.

All configuration settings are clearly visible. Tabs help you categorise information between inputs, outputs, advanced machine diagnostics and management tasks.

diagnostic and management tasks. The allowable range for each required entry is clearly visible to help you understand the range of the parameter.

Preset parameters are automatically loaded when using Emerson sensors and transducers.

Real-time data can be displayed during system configuration to verify that wiring, card settings, and instrumentation are healthy and properly connected.

Real-time information such as gap voltage, waveform data, dcs-sis.com and overall vibration data can be viewed.

Ongoing maintenance functions such as resetting latching relays or loading saved configurations can be easily performed via software.

The software can be run on a PC or laptop.

The System Configuration Software allows you to configure the following monitors of the A6000 series

The following monitors of the A6000 series can be configured:

a6110. a6120. a6125. a6140. a6150. a6151. a6210. a6220. a6310. a6312. a6312-8.

a6410. a6620. a6630. a6740.a6740-10. a6824. a6824r

Menu

Search for products

Back to Top
Product has been added to your cart