Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0

Category: Industry Trends

Home / Industry Trends (Page 154)
March 24, 2025 BY
IN GE

VME-3122A High Performance 16-bit Analogue to Digital Converter (ADC) Board

Features

– 64 different or single-ended inputs

– 16-bit analogue-to-digital conversion (A/D)

– Software selectable conversion rate (up to 100 kHz)

– Programmable selection of scanning 1. 8. 16. 32 or 64 channels

– Continuous digitisation of selected input dcs-sis.com channels and storage of results

– Three trigger modes

– Software triggered

– External trigger

– Interval timer trigger

Three scanning modes

-Automatic scanning

-Single scan

-Random access

– Programmed VME interrupts

– User programmable interval timer

– Software programmable gains of 1 and 10

– External trigger synchronises multiple boards simultaneously

– Jumper-selectable A/D ranges of 0 to +5V, 0 to +10V, ±2.5V, ±5V, and ±10V

– Optional low-pass filter

– Overvoltage protection input

– 1.024 word data buffer (16 word depth buffer x 64 channels)

– Optional output coding

– Power up in auto-scan mode with a gain of 1

APPLICATIONS

– Factory automation

– Process control

– Laboratory Instrumentation

– Machine monitoring

– Data Acquisition

Functional Characteristics

At +25°C and rated power supply conditions (unless otherwise noted)
March 24, 2025 BY
IN Motorola

Motorola MVME2300 Series VME Boards Processor Modules

MPC60x 32-bit class microprocessor

L1 Cache-16KB/16KB MPC603 or 32KB/32KB MPC604

128MB of onboard ECC DRAM

Up to 1MB of embedded Flash for on-board firmware or user-specified requirements

4MB on-board flash for user-specified requirements

On-board debug monitor with self-testing diagnostic features

Two 32/64-bit PMC expansion slots with dcs-sis.com front panel and P2V/0

64-bit PCI expansion mezzanine connector

8Kx8 NVRAM and full-time clock with replaceable battery backup

One asynchronous serial debug port

Four 32-bit timers, one 16-bit timer, one watchdog timer

10/100Mb/s Ethernet transceiver interface

4-level request program, 7-level interrupter, and 7-level interrupt handler for VMEbus

IEEE P1386.1-compliant PMC slot

The MVME2300 has dual PMC ports with front panel and P2 I/O support.

The P2 I/O-based PMC follows the PMC committee recommendations for PCI I/O when using the VME64 expansion connector, and its pin-outs are compatible with the MVME2300.

In addition to providing high-performance expansion I/O, the IEEE P1386.1-compliant PMC port provides a common architecture for future generations of products.

Simply replace the PMC to meet changing I/O needs while reusing the same base platform, reducing long-term cost of ownership.

VME64 Expansion Connector

To maximize the performance of the MVME2300. five rows of 160-pin DIN connectors replace the three rows of 96-pin connectors historically used on VME P1 and P2.

Two additional rows (Z and D) have been added to the VME P1/J1 and P2/J2 connectors to provide additional I/O for the user.

The VME64 expansion connector is fully backwards compatible with existing VME card systems.

PowerPlus Architecture

The PowerPlus Architecture is a processor and bus architecture fully optimized for use from the PowerPC architecture microprocessor family,

The PowerPlus Architecture is a processor and bus architecture that is fully optimized for maximum performance from the PowerPC architecture microprocessor family, PCI bus and VME bus. The outstanding performance of VME processor boards based on the PowerPlus architecture is not due to a single factor.

The processor memory subsystem, the high-speed local bus, the optimized decoupling architecture, the decoupling of the processor from PCI, and the advanced VME bus that reduces PCI latency.

A number of design factors, such as the processor memory subsystem, optimal decoupling architecture, decoupling of the processor from PCI, and advanced VME interfaces that reduce PCI latency, all contribute to the outstanding performance.
March 24, 2025 BY
IN A-B

A-B 2198-S086-ERS3 Single Axis Inverter Module

Product Description: Allen-Bradley 2198-S086-ERS3

The Allen-Bradley 2198-S086-ERS3 features 29.7 kW continuous output power, 22-40 lb*in (2.5-4.5 N*m) torque values, and 560 microfarads of internal capacitance.

About the 2198-S086-ERS3

Allen-Bradley’s 2198-S086-ERS3 Kinetix 5700 single-axis frequency converter is a single-axis frequency converter module that is

for controlling machines with high shaft counts and dcs-sis.com high power requirements. The inverter has current/speed loop bandwidths of 100Hz and 400Hz.

The inverter has a current/speed loop bandwidth of 100 Hz and 400 Hz, a pulse width modulation (PWM) frequency of 4000 Hz, and a continuous output current of 43 A and a 0-pk output current of 60.8 A.

The peak values of continuous and 0-pk output currents are 86A and 121.6A, respectively, and the rated output power of the inverter is 29.7KW.

It requires a DC input current of 45.7ADC and has an internal capacitance of 560μF.

The 2198-S086-ERS3 is rated at 4.6A for non-braked servo motors.

The rated control power for a braked servomotor is 9.6A, and the inrush power at startup is 4A.

Rated power output percentage is 190 watts at 20%, 225 watts at 40%, 325 watts at 60%, 300 watts at 80%, 300 watts at 100

It has a maximum power dissipation of 190 watts at 20% of rated power output, 225 watts at 40%, 325 watts at 60%, 300 watts at 80%, and 475 watts at 100%.

The 2198-S086-ERS3 has an operating temperature range of 0 to 50 °C (32 to 122 °F) and a humidity limit of 5 to 95% non-condensing.

It can be stored over a temperature range of -40 to 70 °C (-40 to 158 °F). Even when installed at an altitude of 1.500 meters (4.921 feet), the

Even when installed at an altitude of 1500 meters (4921 feet), it will not be downgraded and will maintain optimal functioning under 2 G of operating vibration and 15 G of shock.

The 2198-S086-ERS3 provides motor and auxiliary feedback through feedback connections on the 2-pin Motor Feedback (MF) connector and 15-pin Universal Feedback (UFB) connector.

It also supports EtherNet network connectivity through the Ethernet port on the inverter and a 0.15-meter (6-inch) Ethernet cable.
March 24, 2025 BY
IN Emerson

Emerson A6140 Dual Channel Shaft Absolute Vibration Monitor

Functional Features:

Dual-channel, 3U-sized, 1-slot plug-in modules cut cabinet space requirements in half compared to traditional four-channel 6U cards

API 670-compliant, hot-swappable modules

Pre/post buffered and proportional outputs, 0/4-20 mA outputs, 0 – 10V outputs

Self-test features include monitoring hardware, power inputs, hardware temperature, sensors and cables

Used to connect a displacement sensor and a seismic or piezoelectric sensor

or piezoelectric sensor so that the combined output is an absolute value of the axis relative to free space

For use with displacement transducers 6422. 6423. 6424. and 6425 as well as actuators CON 011/91. 021/91. 041/91. and case-mounted piezoelectric velocity sensors

The Shaft Absolute Vibration Monitor is designed for high reliability in the plant’s most critical rotating machinery.

This 1-slot monitor is used with other AMS 6500 monitors to form a complete API 670 machinery protection monitor.

Applications include steam, gas, compressor and hydraulic turbine machinery.

The primary function of the absolute shaft vibration dcs-sis.com monitoring module is to accurately monitor absolute shaft vibration, to

The main function of the shaft absolute vibration monitoring module is to accurately monitor shaft absolute vibration and reliably protect the machinery by comparing the vibration parameters to alarm setpoints and actuating alarms and relays.

The shaft absolute sensor system consists of a relative displacement sensor and a vibration sensor mounted in the same housing.

The displacement sensor is a non-contact sensor that measures shaft position and movement relative to the housing, the

while the vibration sensor mounted in the housing is used to measure the absolute position of the housing relative to free space.

The two sensors are phase compensated for different units and mathematically subtracted to obtain the absolute displacement of the shaft relative to free space.

Absolute shaft vibration is an important measurement used for prediction and protection monitoring on all sleeve bearing machines.

Absolute shaft vibration should be selected when the bearing box and rotor masses are closely matched, as the bearing box may move significantly during machine operation.
March 24, 2025 BY
IN Emerson

Emerson PR 6423 Non-Contact Eddy Current Sensor

The PR 6423 is a non-contact eddy current sensor of rugged construction designed for extremely critical turbomachinery applications, such as steam, gas, compressor and water turbomachinery, blowers and fans.

Examples include steam, gas, compressor and water turbomachinery, blowers and fans.

The purpose of the displacement probe is to measure position or shaft motion without contacting the surface under test (rotor).

In sleeve bearing machines, a thin film of oil separates the shaft from the bearing material.

The oil acts as a damping agent so that shaft vibrations and position are not transmitted through the bearing to the bearing housing.

Vibrations due to shaft movement or position are greatly attenuated by the action of the bearing oil film.

The use of housing vibration sensors to monitor sleeve bearing machines is therefore discouraged.

The ideal method of monitoring shaft position and motion is through the bearing or a non-contact eddy current sensor mounted inside the bearing.

PR 6423 is commonly used to measure machine shaft vibration, eccentricity, thrust (axial displacement), differential expansion, valve position and air gap.

Non-contact measurement of static and dynamic shaft displacements

– Shaft and radial displacement (position)

– Shaft eccentricity

– Shaft vibration (motion)

Meets international standards DIN 45670. ISO 10817-1 and API 670

Rated for use in explosive areas, Eex ib IIC T6/T4

Other displacement transducer options include PR 6422. PR 6423. PR 6424. and PR 6425

Choose from CON 011/91. 021/91. 041/91 and other converters and cables for a complete transducer system
March 24, 2025 BY
IN GE

139-H-FLC Full Load Current Output Option Relay

The 139-H-FLC relay can be supplied with ground fault current and it will accept all current carrying conductors through the ground fault current window.

Please note that it is highly recommended that at least two current leads need to be wound together to minimize noise pickup on the relay.

There is a specially designed current that can be used to dcs-sis.com help output lower level signals.

Frequently Asked Questions about the 139-H-FLC

What is the memory capability of the 139-H-FLC multi-wire general purpose motor protection relay?

This 139-H-FLC is designed to electronically record up to 30 minutes of memory to simulate heat buildup in a motor.

If no overload occurs during this 30 minute period, the memory will be refreshed.

However, if an overload occurs or the motor starts, the circuitry remembers these conditions and can reduce the amount of time available for future overload conditions.

If the motor enters a trip condition due to overheating, the relay will latch to restart for at least 30 minutes to allow the motor to cool.

Motor start trip conditions and overload conditions may cause the motor to heat up, hence the 30 minute lockout time.

Blocked-Rapid Trip, Short Circuit, Unbalance, or Ground Fault conditions do not cause heating and enable the turntable to perform an immediate system reset.

Can users customize the 139-H-FLC Multi-Wire Universal Motor Protection Relay for specific motors?

Users can select from 15 different operating profiles for the 139-H-FLC Multi-Wire Universal Motor Protection Relay.

Four switches are used to select the desired operating profile. The user can find the manufacturer’s data for the motor

Plot the data on the run curve to customize the 139-H-FLC to the motor that needs to be protected.

The full load current from terminals one and two on this model will be proportional to the percentage of full motor current.

Current levels will not be affected by any different wiring lengths.
March 24, 2025 BY
IN ABB

ABB Ability Symphony Plus Distributed Control System (DCS)

The new SDe series continues to innovate to address one of the biggest challenges facing control system owners: upgrading existing infrastructure without disrupting operations.

By preserving field wiring, terminal units and modular wiring, SDe solutions

Helping plant owners protect process controllers, I/O modules and automation technology as it evolves

their Symphony Harmony and INFI 90 investments while dcs-sis.com process controllers, I/O modules and automation technology evolve, enabling progressive growth with minimal impact.

The SDe I/O family includes a range of intelligent analogue, HART, digital and hybrid I/O modules with redundancy that

can communicate with higher-level controllers via the local bus.

Each module is supplied with an evolved mounting base for Harmony Rack systems and is fully compatible with HR BRC410 and SD controllers.

The SDe Series I/O product line includes digital and analogue modules for horizontal or vertical DIN rail mounting and integration with intelligent field devices and protocols.

Hardwired I/O and fieldbus I/O co-exist, using the same library of function blocks to build real-time control applications.

Legacy SDe series analogue input modules interface with field inputs.

such as pressure and flow transmitter signals, thermocouple inputs, and resistance temperature device (RTD) inputs.

Analogue output modules provide output signals to regulate final control elements such as control valves, positioners, actuators and more.

The input channels of the SDe Series digital input modules read the status of switches, relay contacts, solenoids, etc. The digital output modules are available in DC or DC output versions.

Digital output modules provide output channels for DC or AC switching applications.

The digital outputs can be used to drive alarms and bistatic final control elements such as actuators, relays, and solenoids.

For SDe Series digital I/O, each channel can be individually configured as an SOE (sequence of events) point.

This flexibility eliminates the cost and complexity of assigning additional digital inputs as SOEs in the field.

Whether the I/O is locally or remotely located, SOEs with 1 ms time stamps can be used throughout the system.

The SDe family of ruggedised control and I/O products dcs-sis.com provides seamless interconnectivity with intelligent field and electrical equipment and more advanced applications.

Extreme operating temperature ranges and scalable architectures are offered in a compact modular space.

In addition, the series features sustainability improvements, such as reduced power consumption and the use of standards-based technology, which reduces the total cost of ownership for plant owners.

The main principle behind the SDe range is to develop, enhance and extend ABB’s existing INFI 90. Harmony and Symphony DIN (SD) systems.

These systems are currently installed at more than 7.000 sites worldwide.

For Harmony rack mounting, the SDe Series offers increased modularity, enhanced functionality, one-to-one module replacement and space-appropriate mounting options to ensure seamless growth.

Fully compatible with the SD Series, it supports the expansion of SD systems with the latest technology and I/O hardware and software, delivering increased performance, reliability and capacity.
March 21, 2025 BY
IN Woodward

Woodward CPC-DX Redundant Skid Mounted Current Pressure Converter

Manual isolation valves are included in the package, allowing the user to easily repair or replace each individual current-to-pressure converter.

Both automatic and manual transfer logic is available for this skid block assembly, depending on the design of the system.

The skid block’s automatic transfer logic simplifies system design because it does not require external relay/switching logic to operate.

This minimises wiring at the converter-to-converter and control-to-converter interfaces.

The CPC’s configurable alarm/shutdown logic allows the user to easily configure which system conditions force an automatic transfer from the master CPC to the slave CPC.

The manual transfer feature is also available for systems where the user wishes to switch between pressure converters via external logic or manual switching.

The master select discrete input is used to allow the user to dcs-sis.com easily and quickly select the desired control CPC.

An integrated oil pressure gauge allows the user to visualise which converter is in control and verify the skid’s output oil collector pressure level.

Discrete output relay contacts can also be connected to system indications (lights, lamps, plant DCS) to assist in system operating condition monitoring.

Features:

Anti-fouling .

. No small passages to block .

.111 N (25 lb) rotary chip shear .

. Self-cleaning valve design

Automatic and manual switching

Fast changeover time

. Minimised system disturbances

Precise pressure control

Increased reliability

. High Pressure Signal Selection Design

. In-line Repairable

. Master/Slave Logic

Includes isolation valves

Protected with padlock

Large pressure gauge

Remote master/slave indication

Compact size

Available in 10 and 25 bar models

Division 2 and Zone 2 Hazardous Location Approved
March 21, 2025 BY
IN Reliance

Reliance WR-D4008 Programmable Logic Controller

Product Description.

The Reliance Electric PSC7000 WR-D4008 PLC module is an advanced programmable logic controller designed to streamline industrial processes.

It offers superior control features, robust performance and seamless integration with existing automation systems.

The module is a reliable solution for industries seeking an efficient and cost-effective automation solution.

Features

1. High-speed processing: The PLC module has a powerful processor for high-speed data processing and fast response times.

2. Expandable I/O capacity: With its expandable I/O capacity, the module can accommodate a variety of input and output devices for flexible system configuration.

3. User-friendly interface: The module features an intuitive and user-friendly interface that simplifies programming, monitoring and troubleshooting tasks.

4. Powerful Communication Capabilities: Supports a variety of communication protocols for seamless integration with other devices and systems.

5. Enhanced Security: The PLC module integrates powerful security features to protect sensitive data and prevent unauthorised access.

Applications

Reliance Electric PSC7000 WR-D4008 PLC modules are used in a wide range of industrial applications, including:

1. Manufacturing: Optimise production processes, monitor equipment performance and ensure precise control of key parameters.

2. Energy: the module helps to manage power distribution, monitor energy consumption and control renewable energy systems.

3. Oil & Gas: Facilitates remote monitoring and control of pipelines, storage tanks and drilling equipment to improve operational efficiency and safety.

4. Water treatment: The PLC module assists in the automation dcs-sis.com of water treatment plants to ensure precise control and efficient operation.

5. Transport: It can effectively control and monitor traffic systems, railway networks and airport infrastructure.

Technical Specifications

The technical specifications of Reliance Electric PSC7000 WR-D4008 PLC module are as follows:

1. Processor: Advanced 32-bit processor with 100 MHz clock speed.

2. Memory: 256 KB RAM and 2 MB flash memory for programme storage.

3. I/O capacity: Up to 4096 digital I/O points and 128 analogue I/O points.

4. Communication ports: Multiple serial and Ethernet ports for seamless connectivity.

5. Operating temperature: -10°C to 60°C (14°F to 140°F) for reliable performance in a variety of environments.
March 21, 2025 BY
IN Woodward

Woodward APECS™ 0175 Engine Linear Actuator

Description

APECS™ 0175 linear actuators deliver precise positioning and form the foundation of a full electronic governing system. 

Many of the moving parts normally associated with electric actuators dcs-sis.com are eliminated, prolonging the MTBF (mean time between failure). 

The actuator design employs the principle of variable reluctance for consistent force over the entire stroke. 

This simple design of a proportional electric linear actuator utilizes a linear armature whose magnetic force is proportional to the input current to the coil. 

These actuators are easy to install by mounting near the fuel system with a direct connection to the fuel control rod or level. 

In most installations, the normal rotary-torotary connection is eliminated, resulting in a more trouble-free and accurate control system. 

APECS 0175 actuators are suitable for installation on diesel, gasoline, or natural gas engines with fuel system force requirements of less than 4.0 pounds (17.8 N) of force. 

Woodward also manufactures 0175 actuators integral to the engine block or fuel pump. 

Menu

Search for products

Back to Top
Product has been added to your cart