Archives

The IC200CH003 is a connectorized I/O carrier from GE Fanuc Automation.

The IC200CH003 I/O carrier weighs 0.113 kg and has a 36-pin connector for input/output cables.

The carrier provides backplane communication, mounting, and field wiring for one input/output module.

You will find a module latch hole for securing the module to the carrier.

The carrier also provides quick connections for wiring up to 32 input/output points and 4 common power connections.

During rail mounting, the IC200CH003 I/O bracket snaps easily into the DIN rail.

The dimensions are as follows: 7.5 mm x 35 mm: 7.5 mm x 35 mm.

For EMC protection, the DIN must be electrically grounded. The rail must also be electrically conductive and corrosion resistant.

The field wiring can be connected directly to the connector itself by means of contacts crimped onto the end of the wires.

I/O devices can be connected directly to the mating I/O terminals. To install a prewired connection cable, place the cable connector over the connector on the carrier and press down until the latch engages the connector.

To remove the cable, you must hold the connector and press the latch upward to release the connector.

Occasionally, the operating equipment may become hot due to high ambient temperatures. In this case, handle the connector carefully.

Do not touch them directly. Also, avoid exposed connector pins.

Connector kits for making customized cables are available and include a connector and a cover, 6 large contacts, 2 screws, and 36 small contacts.

The IC200CH003 carrier can be used with all VersaMax modules except the following, which have higher isolation requirements:

IC200MDL144 4-Point Isolation Module with Voltage Input 240 VAC

IC200MDD850 Hybrid 240 VAC 4-point Isolation Module

Output Relay 2.0A Isolated 8-Point Module

The Versamax IC200CHS003 Carrier is a connectorized I/O carrier.

The IC200CHS003 carrier has a 36-pin connector for connection to I/O cables.

The Versamax IC200MDL743 discrete output module is a GE Fanuc 5. 12. and 24 VDC and 0.5 A rated negative logic output module.

It has 16 current-flooded discrete outputs that switch the load to the negative side of the DC supply. The module does not have any internal fuses for protection.

The output module connects directly to the controller and also allows for “hot” insertion, making installation easy.

The IC200MDL743 discrete output module communicates with the backplane through an I/O rack. The backplane provides the power needed to operate the modules.

It draws 70 mA** from the backplane. It also has an external power supply to provide the required power to the load.

The IC200MDL743 discrete output module has an on response time of 2.1 ms at 0 V DC, an off response time of 0.0 ms, and an output leakage current of 5.30 mA.

It features a compact modular design for easy and space-saving installation. This module does not provide group-to-group isolation or point-to-point isolation.

It can be used to drive a variety of output devices such as lamps, relays, and motor starters. Power wiring is recommended,

control wiring and communication signal wiring separately to minimize insulation failures and wiring errors.

There are different types of brackets, such as box brackets and spring-loaded compact brackets, to make the wiring process easy.

The IC200MDL743 discrete output module features automatic I/O addressing to maximize ease of use in PLC-based industrial control applications**.

The IC200MDL743 is a discrete signal output module from General Electric’s VersaMax family.

The device has 16 output points, each of which can be either negative logic or sinking type.

The IC670GBI102 is a Genius bus interface module manufactured by GE Fanuc.

The module is part of the Field Control family and is primarily used to realize distributed I/O architectures by connecting field control I/O modules to host GE CPUs via a Genius bus network.

It features a series of screw terminals for terminating the Genius main bus and optional redundant buses; one (1) 9-pin D-shell display port for connecting a handheld programmer (D-Shell); and a 9-pin D-shell display port for connecting a handheld programmer (D-Shell) to the host computer.

It is capable of hosting up to eight (8) field control I/Os and supports standard Profibus transfer speeds, such as 153.6 Kbaud.

It is capable of hosting up to eight (8) field control I/Os and supports standard Profibus transfer speeds such as 153.6 Kbaud standard, 153.6 Kbaud extended, 76.8 Kbaud, or 38.4 Kbaud.

About the IC670GBI102

The IC670GBI001 is a communication module for the GE Fanuc field control series. The module specifically supports the Genius Bus protocol, allowing users to realize distributed I/O architectures.

The module is used in conjunction with the Genius Bus Interface Unit terminal block for DIN rail or panel mounting.

The terminal block also carries screw terminals that allow the establishment of a master Genius Bus connection and an optional redundant network connection.

The IC670GBI001 supports a daisy-chain topology on both the primary and secondary buses.

The module supports data transfer rates of 153.6 Kbaud standard, 153.6 Kbaud extended, 76.8 Kbaud, or 38.4 Kbaud.

Available memory allocations for various data types, such as 256 bytes for discrete inputs (%I), status data, and smart modules; 256 bytes for discrete outputs (%I), status data, and smart modules.

256 bytes for discrete outputs (%Q) and fault clearing for smart modules; 256 bytes for analog inputs (%AI) and 256 bytes for analog outputs (%AQ).

Both the primary and secondary bus connections have a terminating resistor connection point, which is used to terminate the bus connection and maintain a stable connection throughout the network.

The IC670ALG230 has a built-in analog-to-digital converter (ADC) circuit that converts received analog signals into digital format for processing by the host CPU.

The ADC circuit has a conversion time of 1 μs per channel at a module clock of 60 MHz. it also has a first-order RC input filter with a typical conversion capability of 1 Hz.

The module has a nonlinearity of +/- 160% of full scale, a temperature coefficient of +/-.25% per Celsius value, a typical value of +/-.002% per Celsius value, and a ** value of +/-.002% per Celsius value.

**value of +/-.005% per degree Celsius value. The module comes with a single set of input channels and supports single-ended wiring configurations.

Each channel has ground and logic isolation and is rated at 1500 VAC for 1 minute and 250 VAC.

It has a rated current consumption of 51 mA** from the BIU power supply.

The IC670ALG230 input module is an 8-channel input module manufactured by GE Fanuc.

It can be operated with a universal power supply. It is powered by a 24-volt power supply that also powers the Bus Interface Unit.

In the case of isolation, a separate power supply is used. There are LED indicators on the front of the module that show the operation of the backplane and the field power.

The input module is used to drive the different isolated sensors and inputs using the local power supply. There is no isolation between points in the group.

Isolation is rated at 250 volts AC to the enclosure and 1500 volts AC to ground for a continuous period of 1 minute.

The input impedance of the module is 2.87 kohms. turn-on voltage is between 15 and 30 volts dc, and turn-off voltage is between 0 and 5 volts dc.

The response time of the IC670ALG230 input module is between 25 and 60 us, and the power-down response time is between 100 and 150 us.

This module draws 100 mA of current from the bus interface unit. Output keying in this module can be used to mix inputs and outputs.

The input module should be properly grounded to reduce immunity, signal co-domain, and reference points. The loop powered transmitters in the module should use the same power supply.

Frequently Asked Questions about 745-W2-P15-G1-LO-A-R

What is the FlexLogic feature included with the General Electric Multilin 745-W2-P15-G1-Lo-A-R Transformer Protection System?

The FlexLogic of the 745-W2-P15-G1-Lo-A-R Transformer Protection System allows the unit to compute PLC equations by using logical inputs and protection elements that can be adapted to any output.

What options does the General Electric Multilin 745-W2-P15-G1-Lo-A-R Transformer Protection System have?

The General Electric Multilin 745-W2-P15-G1-Lo-A-R Transformer Protection System has the A and the R options which indicate analog inputs and outputs and a restricted ground fault.

What testing capabilities does the GE Multilin 745-W2-P15-G1-Lo-A-R have?

The Multilin 745-W2-P15-G1-Lo-A-R has features that make it a great transformer protection system. It has simulation and testing features so that the operator can test the relay operation  by looking at either waveform data that is captured in the field or that is generated by a computer. This waveform data is then digitized and can be played back. Waveform data can also be recorded to look at fault, alarm, or inrush situations and conditions.