Year: 2025

The IC695ALG626 is capable of providing sixteen (16) input channels if configured for single-ended inputs and eight (8) inputs for differential wiring. By supporting the HART protocol, each channel can communicate with an external HART communicator to access not only readings, but also other HART parameters.

The IC695ALG626 has LED status indicators such as the Module Normal, Field Status, and TB LEDs.The Module Normal LED is used to indicate that the module is configured correctly when the LED is green and constantly lit; if it is slowly blinking green or amber, there is an error; if it is blinking rapidly, the module is not configured correctly; and if the Module LED is off, there is a fault or no power.

The field status LED is green and always on, indicating that there are no faults on the enabled channel and when the terminals are present; amber indicates that the module’s channel is in a faulty state, and an extinguished LED indicates that the terminals are disconnected or incorrectly installed. The TB LED lights up red when no terminals are connected; it lights up green when terminals are connected and goes out if there is no backplane power.

The GE Fanuc IC695ALG626 module is an analogue input module with HART or High-Speed Addressable Remote Sensor Version 5.0 communications on each channel and four internal HART modems. The module provides 8 differential input channels and 16 single-ended input channels.The GE Fanuc IC695ALG626 analogue input module has a voltage range of +/-10 volts dc, 0 to 10 volts dc, +/-5 volts dc, 0 to 5 volts dc, or 1 to 5 volts dc.

The current configuration of the input channel can range from 0 to 20 mA, 4 to 20 mA, or +/-20 mA. If the channel uses HART communication, the GE Fanuc IC695ALG626 analogue input module should be configured for a current range between 4 and 20 mA.

This IC695ALG704 has a channel output data format that can be configured as a floating point IEEE 16-bit or 32-bit integer in a 32-bit field. Each output socket is updated at a rate of 8 milliseconds and has individual overvoltage protection of -60V for 30 seconds and +3V for 30 hours.

The module runs with an RX3i CPU version 0.5 or higher and is programmed using Machine Edition 0.3 SP3 Logic Developer- PLC. It is a single-slot module that mounts to a generic RX695i backplane.

The GE Fanuc IC704ALG3 Non-Isolated Analogue Current or Voltage Output Module requires an RX3i CPU with firmware version 3.0 or higher to run and is mounted in the general purpose backplane of an RX4i PacSystem PLC. The module has 695 channels of current or voltage outputs.The GE Fanuc IC704ALG10 analogue output module has a voltage range of +/-0 volts DC or 10 to 0 volts DC and a current range of 20 to 4 mA or 20 to 850 mA.

The module also features an output load of up to 8 ohms, an update rate of 375 milliseconds, a current rating of 160 milliamps at +3.3 volts DC, and a current rating of 24 milliamps at +24 volts DC isolation. Isolated 1 volt DC power is received from an external power supply connected directly to the module terminals. The power supply cannot be connected through the TB695 connector on the RX3i PACSystem Universal Backplane.

The IC695ALG708 has a built-in module fault reporting feature and retains the last state or output default settings. For CPU compatibility, any RX3i CPU can be used with this analogue output module, however, the CPU must have firmware version 3.5 or later and must be configured using Machine Edition version 5.0 SP3 Logic Developer must be used to develop the user program.

The IC695ALG708 requires an external 24 VDC power supply to operate. The power supply must be connected directly to the module terminals. Compatible terminals for use with this module are box (IC694TBB032), expansion box (IC694TBB132), spring-loaded (IC694TBS032), or expansion spring-loaded (IC694TBS132) terminals.

The analogue module known as IC695ALG708 Analogue Module is designed and manufactured by GE Fanuc and is intended for use with GE RX3i PACSystems devices. The module can be configured for different current and voltage output ranges and can be mounted in the common backplane of the RX3i system.The IC695ALG708 module has eight available output channels that can be customised for voltage or current output operation.

The module supports voltages ranging from 0 to +10 volts or -10 to +10 volts and currents ranging from 0 to 20 mA or 4 to 20 mA. All outputs are non-isolated and the module can be used in combination with many different terminal types. The module’s backplane requires a 3 mA current rating at 375.3 volts.

The IC695CBL002 cable is a replacement cable used to connect the CPU unit to the energy pack of GE Fanuc’s RX3i PACSystem.

The cable comes with a 7-pin keyed connector and is 1 metre (36 inches) long. The system operates on 120/240 volts DC,

125 Vdc or 24 Vdc, and compatible energy packs can be mounted on DIN rail.

The GE Fanuc IC695CBL002 cable is a replacement cable used to connect the RX3i PACSystems Series CPU to the optional energy pack.

The cable is made of the best materials for typical industrial use and is coated to provide the necessary protection for use in harsh environments.

The IC695CBL002 cable connects to the connectors located at the bottom of the CPU and energy pack.

These components are manufactured in accordance with the EU RoHS Directive 2011/65/EU and they are powered by a voltage range of 120/240 volts DC,

125 Vdc or 24 Vdc. The IC695CBL002 cable has a 7-pin keyed connector and is 1 metre (36 inches) long.

Custom lengths are available for GE accessory cables like this one, but 1 metre is the standard length for this type of application.

The PACSystems RX002i Energy Pack, compatible with the IC3CBL695 cable, can be mounted on a DIN rail like the EN50022 rail.

but can also be mounted on a panel where other equipment is placed. The catalogue number of the compatible Energy Pack module is IC695ACC402.

The CEP tray is a powerful system component with standard features such as complete programming and configuration options via Proficy Machine Edition software, and support for multiple network topologies.

USB port for all necessary firmware upgrades, improved troubleshooting and advanced remote node module scanning.

The IC695CEP001 CEP carrier operates over a voltage range of 19.2 to 30 volts DC.

It produces 25.0 watts (22.24 amps) of power at a nominal voltage of 5 volts DC.

The system allows one I/O module per station, for a total of 1024 bytes of I/O data per station.

In addition, the GE Fanuc IC695CEP001 carrier module allows up to 512 bytes of I/O data per station for input and output data.

The module supports PROFINET version 2.3 (Class A) and requires Proficy Machine Edition version 8.0 SIM 5 or higher.

The CEP carrier also has 32 input status bits and 32 output control bits.

The IC695CEP001 CEP carrier module is part of a high-speed running I/O LAN system.

The physical characteristics of the IC695CEP001 carrier module include the following dimensions: 177.2 x 51 x 35 mm (7 x 2 x 1.3 inches).

The component operates over a temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit).

The IC695CHS007 is ideal for applications with limited mounting space or for the implementation of remote I/O architectures. The module comes with a 24 VDC terminal strip located at the left end of the rack. Backplane grounding points and an integrated ground strip are provided for connecting the shielding and grounding connections of the rack-hosted module. The slot number is also clearly printed on this rack so that the module can be installed accordingly.

There are two (2) versions of this IC695CHS007. specifically the initial version, IC695CHS007-AA, and the subsequent version, IC695CHS007-BA, which include mechanical enhancements, specifically the chassis’ backplane PCI connectors.

This IC695CHS007 is for horizontal casting only. Other mounting orientations may affect airflow and ultimately system performance. This rack mounts directly to the chassis panel through the mounting holes provided in the chassis.

Inputs

Number of channels

– 8. single-ended

Nominal Signal Range (Scale)

– 4 to 20 mA

Full signal range

– 1 to 23 mA

Line Fault Detection

– Short circuit current – > 23.5 mA

– Open circuit current – < 0.5 mA

Output voltage (@ 20 mA)

-13.5 V (min.)

Output current

– 32 mA (max)

Accuracy (over temperature range)

– ± 0.1% of range

Resolution

– 16 bits

Repeatability

– 0.05 of range

Isolation

– Any channel to rail bus – 100 V ac

– Between channels – none

Configurable parameters

Alarms

– High, High-High, Low and Low-Low

Alarm deadband (hysteresis)

– User-defined values

Input Filter Time Constant

– User-defined value

Input Deadband

– User-defined value

Drive is in a fail-safe state

– Disable/Upconversion/Downconversion

Channel Status

– Active / Inactive

HART variables and status reports

– Enabled / Disabled

Response time

Signal change to railway bus availability

– 4-20 mA mode – 27 ms (maximum)

– HART mode – 0.75 seconds per channel

Safety

FM Non-Flammable Field Wiring Parameters

(per channel)

– Voc = 28.7 V; Isc = 33 mA; Ca

= 0.17 μF; La

= 11.0 mH

Power Supply

Rail bus (12V) Current

– 100 mA (typical)

– 150 mA (maximum)

Bus Field Power

– 2-wire Tx – 300 mA (max)

– (@ 24 VDC ±10%) 4-wire Tx – 60 mA (max)

Mechanical

Module Key Codes

– A1

Module Width

– 42 mm

Module weight

– 200 g

Hardware Tips and Specifications

While there is not a great deal of factory-released original manual IS215SECAH1A information available online, there is not a great deal of original manual information about the printed circuit board, but some useful material suggests that its status as a solar MACC-BPPB-WEMD component is a strong starting point. Additional information on the series and individual product status of the IS215SECAH1A boards can be obtained by careful visual inspection with a supplementary breakdown of the individualised IS215SECAH1A product numbers. For the uninitiated, two of the more obvious hardware components integrated into the IS215SECAH1A PCB substrate can be recognised in the standard issue Ethernet ports, which are placed longitudinally across each other on the large printed circuit board. Although the IS215SECAH1A board itself contains no other Ethernet ports, the centre of the BPPB board to which it is attached has two identical Ethernet ports. The drive manager has access to eight other ports that connect to this IS215SECAH1A board. These ports are all female and are attached to the edges of the IS215SECAH1A board during factory installation by using screw brackets to improve connection efficiency.

In addition to the various female ports available to users of the IS215SECAH1A board, a series of integrated circuits are integrated into the design of this SECA module. Each of them should be labelled with an individual reference mark, and some of them appear to carry their own factory-applied reference labels with individual component specifications. The final obvious standout hardware feature for the IS215SECAH1A’s circuit board assembly is its series of factory drilled holes. These factory-drilled holes, which are used for mounting purposes, are insulated for complete surface and internal voltage protection, and they are present on the IS215SECAH1A board in a total of five.