Month: May 2025

The IC697PCM711 module is a programmable coprocessor module from GE Fanuc.

This single-slot programmable coprocessor module is part of the GE 90-70 series and has a dual-task module that can be programmed to perform different functions.

The different functions that the IC697PCM711 module can be programmed to perform include real-time calculations, operator interface functions, and data functions.

The IC697PCM711 module is used to perform operations related to storage, acquisition and communication applications.

Communication between the module and the PLC CPU is achieved via the backplane and does not require application support.

The IC697PCM711 module has multiple PCMs supported by a single IC697 PLC system and can accommodate up to 512 KB of optional expansion memory.

The IC697PCM711 module operates with an extended memory daughter board. It has a base memory with a maximum capacity of 95 KB of user memory.

The Expanded Memory Daughterboard can expand the data or programme memory to 64. 128. 512 or 2586 KB.

The IC697PCM711 module requires a 1-amp power supply, which is available from a 5-volt bus. When installed, the IC697PCM711 module should be referenced to the applicable programmable controller.

Be sure to disconnect rack power and install expansion memory where needed. In addition, it is necessary to connect the battery to either of the connectors provided with the unit.

The IC697PCM711 module can be operated without the expansion memory daughter board.

It can be programmed and configured simply by connecting an IC647 or IC640 computer or using an IBM compatible PC.

Description: The IC200MDD840 is a 32-point combination discrete I/O module in the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now part of Emerson Automation. The module has twenty (20) 24 VDC positive logic inputs and twelve (12) Type A 2.0 Amp rated relay contact outputs. The module has a maximum backplane current draw of 375 mA.

About the IC200MDD840

The IC200MDD840 is a component module in Emerson Automation’s VersaMax product family, formerly known as the General Electric Intelligent Platform (GE IP). The module is a combinational I/O module with embedded discrete input and output circuitry such as ten (10) positive logic 24 VDC inputs and twelve (12) A- or normally open (N.O.) contact outputs. The module has a maximum backplane current of 375 mA.

The input channels are divided into two (2) groups of ten (10) input channels each. Input characteristics include: input voltage compatibility from 0-30 VDC (24 VDC nominal); on-state voltages from +15 to +30 VDC; off-state voltages from 0 to 0.5 mA; typical on-state and off-state signal transition delays of up to 0.5 ms; and input impedance of up to 10k ohms. The input channels have configurable filtering times for both electrically and mechanically noisy input channels, eliminating false-positive and false-negative signals. These filter times include 0 ms, 1.0 ms, and 0.7 ms, with the default configuration being 1.0 ms.

The relay output channels are divided into two (2) groups dcs-sis.com of six (6) channels each. The contact outputs are rated at a minimum of 10mA per point; maximum current per module is 8.0A; 2.0 amps at 5 to 265VAC, maximum with resistive load; 2.0 amps at 5 to 30 VDC, maximum with resistive load; and 0.2 amps at 31 to 125 VDC, maximum with resistive load. Module relay types are fixed coil, moving armature, and silver alloy contact types.

About the IC200ALG432

The GE Fanuc IC200ALG432 module is a hybrid analogue module that uses a 10-volt DC power supply.

It is a 12-bit module with four channels and two output channels. The analogue module has an update rate of 0.4 ms and an input response time of 5 ms.

The analogue module requires an external power supply to power the outputs. The inputs of the module are powered by an external power supply for the transceiver.

The CPU in the module is responsible for processing the operation.The LEDs on the front of the IC200ALG432 module indicate the flow of power and backplane current.

There is no thermal derating with this hybrid module. the total current consumption of the IC200ALG432 module during normal operation is 160 milliamps, including load current.

The module’s diagnostic features help detect losses in the user-side power supply.

The GE Fanuc IC200ALG432 module comes with configurable alarms that can be set for different events.

During installation, the module should be protected from electromagnetic noise and airborne contaminants. The temperature of the installation area should not exceed 60 degrees Celsius.

The accuracy of the module depends on the ambient temperature. At 25 degrees Celsius, the accuracy is +/-0.3% of full scale; at 60 degrees Celsius, the accuracy is +/-0.3% of full scale.

At 60 degrees Celsius, the maximum accuracy is +/-1%. IC200ALG432 modules have a resolution of 8 counts.

The common mode voltage of the module is 0 V. The IC200ALG432 module has a bus current consumption of 60 mA when operating from a 5 V supply.

The GE Fanuc IC200PWR202 module is a power supply module with extended capabilities in the Versamax family.

It has an input voltage range of 9.5 to 15 volts DC, a nominal voltage of 12 volts DC, and output voltages of 5 volts DC and 3.3 volts DC.

About the IC200PWR202

The GE Fanuc Versamax IC200PWR202 power supply module features expanded functionality with up to 3-volt DC extended power supplies.

This module does not have an isolated power supply like other power modules in the Versamax family.

This device can power backpPLC channel devices including I/O modules, CPUs, and NIUs.

It can be used as a primary or secondary power supply in a system, especially when installed on a power booster carrier.

The GE Fanuc IC200PWR202 power supply module has an input voltage range of 9.6 to 15 volts DC and a nominal voltage of 12 volts DC.

Its output voltage is 5 volts DC or 3.3 volts DC. The module has a hold time of approximately 10 milliseconds and is rated at 11 watts of input power.

The GE Fanuc IC200PWR202 power supply module has an inrush current rating of 25 amps at 12 volts DC and 30 amps at 15 volts DC.

The total output current of the IC200PWR202 power supply module should not exceed 1.5 amps. When the output voltage is 3.3 volts DC, the output current is 1.0 amp.

When operating at 5 volts DC output current, the maximum output current is 1.5 amps minus 3.3 volts used.

The power supply module is designed with reverse polarity, short circuit, and overload protection.

The dimensions of the IC200PWR202 power supply module are 49 mm (1.93 in.) x 133.4 mm (5.25 in. x 39 mm (1.54 in.), not including DIN rail or carrier height.

Embedded Ethernet communication ports enable controller and media redundancy, thus increasing the availability of the I/O modules. These Ethernet ports feature a dedicated microprocessor core that allows the IC695CPE330 controller to simultaneously perform up to 48 SRTP server connections and 16 Modbus®/TCP server connections with up to 32 clients (SRTP or Modbux/SRTP) per connection.

In addition, the USB 2.0 master port allows uploading and downloading of programmes using ordinary USB flash drives and smartphones. This feature makes it easy to maintain the operation of the RX3i control system.

The IC695CPE330 supports programming languages such as Ladder Diagram (LD), Structured Text (ST), Function Block Diagram (FBD), or C. The IC695CPE330 also supports communication with third-party devices through OPC UA, an industry standard that can be implemented over Ethernet IP connections.

The IC695CPE330 CPU also supports a variety of IO protocols such as PROFINET, EGD, Modbus TCP, PROFIBUS, Genius, DeviceNet, Modbus RTU, and Reflected Memory (CMX) protocols. It is part of the RX3i family of CPUs with an embedded Ethernet/PROFINET interface.

The IC695CPE330 RX3i PacSystems CPU also supports the Rackmount PROFINET Controller Module for communications.The IC695ACC402 Energy Pack, IC695ACC412 Capacitor Pack, and the IC695CBL002 Connection Cable are some of the optional accessories for this module. The module panel has 6 LED status indicators, pushbuttons, and a 3-position run mode switch for easy monitoring and operation. The CPU must be mounted in the mainframe of an RX3i PLC system to integrate with any RX3i I/O module or Intelligent Option Module. Supporting up to 32K discrete and analogue I/O points, the IC695CPE330 RX3i CPU is the best choice for multi-layer communication and handling large amounts of data in complex industrial applications.

The IC695STK001 Starter Kit is the RX3i PacSystems Package 1 Starter Kit, part of GE Fanuc Automation’s RX3i PacSystems family.

Like the other starter kits, this kit is designed to meet the specific requirements of certain devices used in a PLC system. The kit includes a CPU and software.

The choice of CPU depends on the user and their application, and the different CPUs available include the IC695CPU310. IC695CHS012. IC695LRE001. IC695PSA040. IC695ETM001. IC694ACC300. IC694MDL940 and IC646MPP00 CPUs.

The GE Fanuc Automation IC695STK001 RX3i Package 1 Starter Kit is designed to provide a combination of hardware and software to install the CPU and make it ready for operation.

The CPUs in the GE Fanuc Automation IC695STK001 RX3i Package 1 Starter Kit provide real-time control of different devices in an application process.

These devices can be machines, processors, and material handling systems.

These CPUs share data with connected programmers and HIM devices that display the current status of the application process.

This particular CPU contains battery backed memory and non-volatile flash, configurable data and program memory.

Most 90-30 series modules and expansion racks are supported.