Month: April 2025

The IC200BEM003 module is a master module manufactured by GE Fanuc that sends and receives data on a PROFIBUS network.

It is compatible with Versamax, PROFINET and CPU 005 systems.

About IC200BEM003

The IC200BEM003 module is a Versamax master module designed by GE Fanuc.

It can easily send/receive data on a V1 PROFINET network. It supports variable data rates.

A total of 3584 bytes of input data and 3584 bytes of output data can be processed using this module.

The module has synchronised and frozen modes. dcs-sis.com This network interface module has a data rate range between 9.6 k baud and 12 M baud.

The IC200BEM003 module uses a linear bus network topology terminated at both ends. It uses shielded twisted pair cables for data and information transfer.

The network module is connected using a 9-pin D-sub connector. It is small and compact, measuring 4.3 inches wide by 2.63 inches high by 1.956 inches deep.

The Versamax IC200BEM003 module is an intelligent module with a slave status array list, slave diagnostic addresses, and other features.

It draws a total of 5 milliamps of current from a 450-volt output.The IC200BEM003 module can be configured using a software utility with a host controller and a Windows operating system.

The front of the module has LEDs that light up when there is communication activity.

The IC200BEM003 module* supports up to 125 slave devices and can be configured through software.

Network-to-frame ground isolation is rated at 250 volts AC and PROFIBUS network to backplane is rated at 1500 volts AC for 1 minute.

The module is certified to UL standards for installation in hazardous areas.

Network Interface Module

The Network Interface Module allows the VersaMax PLC to operate as a master or slave on a network.

Currently available modules support DeviceNet master or slave communication and PROFIBUS-DP slave communication. AS-i master communication is also available.

The IC200ALG266 is a 15-point analogue current input module for the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now manufactured by Emerson Automation.

The module features fifteen (15) single-ended input channels that accept -10 to +10 VDC input signals with 15-bit resolution** and an update rate of 7.5 ms.

The module has a **backplane current consumption of 150 mA.

About the IC200ALG266

The IC200ALG266 is a VersaMax dcs-sis.com analogue input module. The module is intended for use in distributed I/O architectures.

It is used to connect analogue measuring instruments and feedback devices to generate a signal voltage range of 10 VDC to + 10 VDC.

The input module has an analogue-to-digital signal conversion resolution of 15 bits or 0.3125mV per count.

The IC200ALG266 is powered by a backplane power supply** with a current consumption of 150 mA. it does not require an external power supply to activate each input channel.

It does not require an external power supply to activate each input channel, as the embedded fifteen (15) analogue input channels support a current sink wiring configuration.

The module has a full-scale accuracy of +/-3.0% at 0 degrees Celsius operating temperature,** a full-scale accuracy of +/-5.25%, and a full-scale** value of +/-60% at 1 degree Celsius.

Each channel of the IC200ALG266 is capable of detecting faults in analogue signal conversion.

This occurs when the output provided by the AD converter is greater than 6% of the full scale value.

This error is reported to the CPU, which can indicate to the partner Human Machine Interface (HMI) and Supervisory Control and Data Acquisition (SCADA) systems as a fault or poor signal quality.

The IC200ALG266 has software configurable input states in response to a CPU stop or module error.

These options include default or *last state operation and are suitable for achieving safe startup, especially in the event of a power interruption.

Filter response is 32 Hz +/-20% per input channel with a channel update rate of 7.5 ms.

The GE Fanuc Automation IC200ALG266 module is a certified Versamax input module manufactured by GE Fanuc Automation.

The module is designed to provide an interface to different input devices. The interface is achieved by connecting to the 15 input channels included in the module.

These inputs are analogue and the module comes with an LED that indicates when the drive is correctly configured and able to operate, this LED is the OK LED.

The GE Fanuc Automation IC200ALG266 Versamax Input Module has protection features that ensure safe operation and help extend the life of the module and inputs.

These protection features protect the module from overvoltage levels above 30 volts DC.

The operation of each input is a separate operation, which means that if one is in a fault condition, it will not affect the function of the remaining inputs.

The GE Fanuc IC200MDD848 module is a discrete I/O module manufactured by GE Fanuc Automation.

It belongs to the Versamax series and has 16 I/O points divided into 2 groups of 8 points each.

About IC200MDD848

The IC200MDD848 module is a discrete I/O module manufactured by GE Fanuc Automation and is part of the Versamax series.

The module has 16 I/O points divided into 2 different groups, each group consisting of 8 points.

The GE Fanuc IC200MDD848 module has positive logic or source-out type inputs and supports channel-to-channel isolation for each discrete output point.

In addition, the IC200MDD848 module provides various protection features for each output point, including metal oxide varistors (MOVs) and buffers.

Although diagnostics are provided, each I/O point is mapped to a status LED.

The IC200MDD848 discrete I/O module is powered by a backplane mounted on the PLC chassis.

However, an external 120 VAC power supply dcs-sis.com is required for any switches that power the loads.

The module has a *minimum* load current of 10 milliamps per input and output point, and a **load current of 5 amps.

It also has a **5 amp load current for a single 20 millisecond cycle.

The IC200MDD848 discrete I/O module draws 5 mA from 125 V peak backplane voltage.

The use of external suppression circuitry is recommended when installing the module’s wiring and configuring the outputs for inductive loads.

The IC200MDD848 module supports thermal derating as well as various I/O combinations. The number of **active points that can be run simultaneously depends on various factors.

Some of these factors include the ambient temperature, the physical location of the DIN rail, the external voltage, and the location of the device itself.

About IC200ALG431

The IC200ALG431 module is a hybrid module from Agfaq. It is a 12-bit device for industrial automation applications.

The analogue module provides flexibility by combining inputs and outputs using a single carrier base.

The front of the module has LED indicators that help the operator understand the flow of power in the module.

The module has “FLD PWR” and “OK” LED indicators. The module is compact in size with a width of 4.30 inches, a depth of 1.95 inches and a height of 2.63 inches.

The IC200ALG431 module weighs approximately 4.4 lbs. The module is equipped with a 0 to 10 volt DC analogue input and a 0 to 10 volt DC analogue output. The module is powered by an external power supply.

The IC200ALG431 module uses shielded twisted pair cable for analogue channel connections.

During module installation, the module should be properly grounded to the source device.

If the module is connected through a carrier using a connector type, it can be connected to the plug-in terminals.

Hybrid modules are equipped with diagnostics that help report circuit faults. The I/O defaults in the module can be used with jumpers.

The IC200ALG431 module draws dcs-sis.com a total of 60 mA from the 5 volt bus interface unit.

The module can be easily installed into a system by using panel mounting.

This is an indoor unit designed with an open architecture. It should be protected from water spray and kept away from heat sources.

The ambient temperature should not exceed 60 degrees Celsius.

Technical description of IC200ALG431

The IC200ALG431 module is an Agfanac module in the Versamax series. It is a 12-bit module.

The IC200ALG320 is a 4-point analogue current output module for the VersaMax I/O family, formerly offered by GE Intelligent Platforms and now part of Emerson Automation.

The module features four (4) single-ended output channels that generate a 4-20 mA output signal with 4 μA resolution** and an update rate of 0.3 ms.

It requires an external power supply of 18-30VDC or 9.6 to 15 VDC.

About the IC200ALG320

The IC200ALG320 is an analogue output module, part of the VersaMax family of distributed I/O modules.

Formerly manufactured by GE Intelligent Platforms, it is now part of Emerson Automation.

The module is typically used as part of a distributed or remote I/O network, often for medium to large control systems, to

Eliminates long signal runs and helps build robust and scalable control systems.

The IC200ALG320 has four (4) single-ended analogue output channels that produce a 4-20 mA output current signal with 4 μA resolution.

It is particularly suitable for automatic closed-loop dcs-sis.com control systems as well as manual or open-loop control systems for analogue signal tracking devices.

Examples include control valves, dampers, shutters, positioners, variable frequency drives (VFDs) and similar operating devices.

It can also be used for signal retransmission purposes, such as providing an output signal representing a calculated variable within a Programmable Logic Controller (PLC).

for terminating signal splitters or signal isolators, panel meters for local readouts, data loggers for historicisation, single loop controllers or other PLCs, and for the use of the PLC as an interface.

single-loop controllers or other PLCs for advanced and complex architectures with cascaded controllers.

The IC200MDL744 discrete output module provides a green “FLD PWR” LED to indicate whether field power is applied to the module.

The IC200MDL744 discrete output module provides a green “FLD PWR” indicator to indicate whether field power is applied to the module and an “OK” LED to indicate the presence of backplane power. It also has a 0.2 ms turn-on response time and a 1 ms turn-off response time.

When inductive loads are connected to the outputs, the use of an external suppression circuit is recommended. The thermal derating of the module depends on several factors.

such as ambient temperature, voltage level, and orientation of the module. It has 250 volts AC, user input to logic,

user input to logic, user input to frame, and group to group isolation voltages. It does not have point-to-point isolation.

The IC200MDL744 Discrete Output Module requires a NIU or CPU in the Versamax PLC to perform intelligent processing for industrial applications.

Features

Powerful, Reliable Performance

VersaMax controllers provide powerful, reliable operation. dcs-sis.com These versatile controllers are designed to minimise cost, are easy to use and support, and offer a wide range of I/O expansion modules and communication options.

Versamax Modularity Provides Exceptional Versatility

VersaMax modularity is control and IO that can be snapped together to provide compact nodes with a smaller footprint than typical control/IO combinations.

Versamax Micro Delivers High Performance in a Small Form Factor

The Micro Series VersaMax controllers offer superior functionality in a compact package. Their modular design provides the functionality and flexibility to meet your application needs.

Large amounts of memory with fast cycle times, powerful instruction sets, and expanded programming options. Programming and configuration is simple and intuitive using Proficy Machine Edition software.

The IC200BEM003 module is a master module manufactured by GE Fanuc that sends and receives data on a PROFIBUS network.

It is compatible with Versamax, PROFINET and CPU 005 systems.

About IC200BEM003

The IC200BEM003 module is a Versamax master module designed by GE Fanuc.

It can easily send/receive data on a V1 PROFINET network. It supports variable data rates.

A total of 3584 bytes of input data and 3584 bytes of output data can be processed using this module.

The module has synchronised and dcs-sis.com frozen modes. This network interface module has a data rate range between 9.6 k baud and 12 M baud.

The IC200BEM003 module uses a linear bus network topology terminated at both ends. It uses shielded twisted pair cables for data and information transfer.

The network module is connected using a 9-pin D-sub connector. It is small and compact, measuring 4.3 inches wide by 2.63 inches high by 1.956 inches deep.

The Versamax IC200BEM003 module is an intelligent module with a slave status array list, slave diagnostic addresses, and other features.

It draws a total of 5 milliamps of current from a 450-volt output.The IC200BEM003 module can be configured using a software utility with a host controller and a Windows operating system.

The front of the module has LEDs that light up when there is communication activity.

The IC200BEM003 module* supports up to 125 slave devices and can be configured through software.

Network-to-frame ground isolation is rated at 250 volts AC and PROFIBUS network to backplane is rated at 1500 volts AC for 1 minute.

The module is certified to UL standards for installation in hazardous areas.

Network Interface Module

The Network Interface Module allows the VersaMax PLC to operate as a master or slave on a network.

Currently available modules support DeviceNet master or slave communication and PROFIBUS-DP slave communication. AS-i master communication is also available.

The IC200ALG266 is a 15-point analogue current input module for the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now manufactured by Emerson Automation.

The module features fifteen (15) single-ended input channels that accept -10 to +10 VDC input signals with 15-bit resolution** and an update rate of 7.5 ms.

The module has a **backplane current consumption of 150 mA.

About the IC200ALG266

The IC200ALG266 is a VersaMax analogue dcs-sis.com input module. The module is intended for use in distributed I/O architectures.

It is used to connect analogue measuring instruments and feedback devices to generate a signal voltage range of 10 VDC to + 10 VDC.

The input module has an analogue-to-digital signal conversion resolution of 15 bits or 0.3125mV per count.

The IC200ALG266 is powered by a backplane power supply** with a current consumption of 150 mA. it does not require an external power supply to activate each input channel.

It does not require an external power supply to activate each input channel, as the embedded fifteen (15) analogue input channels support a current sink wiring configuration.

The module has a full-scale accuracy of +/-3.0% at 0 degrees Celsius operating temperature,** a full-scale accuracy of +/-5.25%, and a full-scale** value of +/-60% at 1 degree Celsius.

Each channel of the IC200ALG266 is capable of detecting faults in analogue signal conversion.

This occurs when the output provided by the AD converter is greater than 6% of the full scale value.

This error is reported to the CPU, which can indicate to the partner Human Machine Interface (HMI) and Supervisory Control and Data Acquisition (SCADA) systems as a fault or poor signal quality.

The IC200ALG266 has software configurable input states in response to a CPU stop or module error.

These options include default or *last state operation and are suitable for achieving safe startup, especially in the event of a power interruption.

Filter response is 32 Hz +/-20% per input channel with a channel update rate of 7.5 ms.

The GE Fanuc Automation IC200ALG266 module is a certified Versamax input module manufactured by GE Fanuc Automation.

The module is designed to provide an interface to different input devices. The interface is achieved by connecting to the 15 input channels included in the module.

These inputs are analogue and the module comes with an LED that indicates when the drive is correctly configured and able to operate, this LED is the OK LED.

The GE Fanuc Automation IC200ALG266 Versamax Input Module has protection features that ensure safe operation and help extend the life of the module and inputs.

These protection features protect the module from overvoltage levels above 30 volts DC.

The operation of each input is a separate operation, which means that if one is in a fault condition, it will not affect the function of the remaining inputs.

The GE Fanuc Automation IC200ALG266 Versamax input module has a backplane current consumption rating of 50 mA to 100 mA.

It cannot be run from an external power supply.The IC200ALG266 Versamax input module has a 15-bit resolution.

However, it may need to be derated by up to +/-2% if it is subject to RF interference. The module filters at a channel update rate of 7.5 milliseconds.

The input current range of the module is -10 VD to +10 VDC.