Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0

Month: February 2025

Home / 2025 / February (Page 2)
February 27, 2025 BY
IN Parker

Parker AC890 Compact Modular System AC Drive

Markets:

“Water and Wastewater Treatment

·Pulp and Paper

·Steel Mills

·Marine

·Cranes

.Wind and Solar Power

.Food and Chemical Processing

Features and Benefits.

The AC890 can be configured for 4 different modes of operation .

open-oop (volts/frequency) control

This mode is ideal for basic, single or multi-motor speed control.Sensorless vector controlWith its ultra high performance sensorless vector algorithm,the Ac890 delivers a combination of both high torgue and close speedregulation without the need for any speed measuring transducer.Closed-loop vector control

Full closedloop flux vector performance can be achieved with the Ac890 by simply adding an encoder feedback ‘technology box. Thisprovides 1 00% continuous full load standstilltorque, plus a highly dynamic speed loop more than suficient for the most demanding applications.

4 Quadrant active front-end power supply moduleharmonic content is achieved (THD< 3%)

With this confauration, the eneray is fed back into the mains supply with sinusoidal currents and unity power factor a very low curen

Applications:

.Slitting Lines

.Hot and Cold Saws

.Forming Rolls

.Printing Lines

.Fans, Pumps, and Blowers

.Water Treatment

.Wind Turbines

.Solar Power

.Engine Testing
February 27, 2025 BY
IN A-B

A-B 1336E-B075-AE-EN-HA2-L6 Adjustable Frequency Drive

It is rated at 380 to 480 volts AC, 56 kilowatts and 75 horsepower.

It is equipped with a programmer/controller with digital potentiometer HMI to simplify drive control and programming.

Up to 16 programmable speed command transitions are available on the drive, which supports SCANport communications and English as the programming language.

The 1336E-B075-AE-EN-HA2-L6 IMPACT drive is designed to provide unrivaled speed control.

The diagnostic features on this drive allow real-time monitoring of its logic board and power structure.

It has 32 entry fault queues and 32 entry warning queues with markers for clearing faults and timestamping power-ups.

Flying start mode on this drive applies to motors that are already spinning loads.

As with all B-frame 1336 IMPACT drives, the 1336E-B075-AE-EN-HA2-L6 drive does not support network connectivity through an isolated gateway.

Its memory storage is non-volatile, and it has a NEMA 1 (IP20)/EMC enclosure and a 115-volt AC control interface.

The function blocks on this drive provide greater flexibility than other drives.

Connecting the 1336E-B075-AE-EN-HA2-L6 IMPACT Drive to a Motor Using a Long Cable

Cable terminators or output chokes may be required to minimize voltage reflections at the motor terminals.

It can be fitted with different types of cables including shielded, unshielded and armored cables.

The drive is designed to use a three-phase power supply that is symmetrical to ground and supports the use of a line reactor or isolation transformer if the power supply encounters power line conditions that could cause a fault.

This 1336 PLUS II adjustable frequency AC drive is a 380-480VAC unit with 56 (75) kilowatts (kW) of power (horsepower) and has an (n) NEMA 1 (IP20)/EMC enclosure.
February 27, 2025 BY
IN GE

IC200ALG630 Analog Input Module

The IC200ALG630 has a backplane current consumption of 3 mA at the 125 VDC and 5.3 VDC outputs on the backplane.

It is also rated for optical and frame-to-ground isolation with a continuous voltage duration of 250 VAC and a 1500 VAC voltage duration of 1 minute.

The module also provides LED status indicators, specifically an OK LED that indicates active backplane power when the module fails, and amber when lit green.

The IC200ALG630 module is GE’s 16-bit analog input module. It is an industrial module designed to handle a wide range of application requirements.

It comes with a 7-bit thermocouple with 16 channels. This thermocouple analog input module receives power from the backplane power supply.

It offers four cold end compensation options, no cold end, remote cold end, fixed cold end, and localized cold end compensation.

It is rated at 5 volts DC. It supports different thermocouples of type J, K, T, S and R.

The IC200ALG630 module is capable of drawing a total of 5 milliamps of current from the 125 volt bus.

The update rate of the analog module is 60 milliseconds for 60 Hz and 50 milliseconds for 70 Hz.

An OK indicator on the front of the module indicates the presence of backplane power.

The IC200ALG630 module has a compact design that saves panel space.

It measures 4.3 inches wide, 2.63 inches high, and 1.95 inches deep.

The temperature range should be set between 0 and 60 degrees Celsius. The thermocouple module has advanced diagnostic features.

It can issue channel-specific alarm reports. It can also detect over- and under-range conditions in the input.

Faults caused by thermistors can be easily detected by the module as internal faults. The module has not experienced thermal derating.
February 27, 2025 BY
IN A-B

A-B 140G-G2C3-C15 Molded Case Circuit Breaker

About Allen-Bradley The 140G-G2C3-C15 Molded Case Circuit Breaker is a thermal magnetic circuit breaker in the 140G circuit breaker series designed to provide short circuit protection for a variety of control panel applications.

As with all 140G circuit breakers, the 140G-G2C3-C15 circuit breaker is sized in accordance with Table 430-152 of the NEC (National Electrical Code).

The 140G-G2C3-C15 circuit breaker is suitable for branch or main circuits operating at 600 volts AC (690 volts IEC).

It has a breaking capacity value of 25 kA (480 VAC) and a current rating of 125 amps.

The 140G-G2C3-C15 circuit breaker has a fixed thermal/magnetic trip device with fixed thermal and magnetic trip ratings of 500 amps and 15 amps, respectively.

The breaker will trip immediately when the current flowing through the breaker exceeds the breaker’s setting.

The 140G-G2C3-C15 circuit breaker provides thermal trip action through the use of its bimetallic element, which deflects high currents when they flow through the circuit for extended periods of time.

It also provides magnetic tripping action by means of a solenoid coil which provides a magnetic field proportional to the current applied to the circuit, thereby tripping the circuit when the current exceeds the set trip value.

The 140G-G2C3-C15 circuit breaker has a rated life of 25.000 operations (240 operations per hour) and an electrical life of 8.000 operations (120 operations per hour).

It has 3-pole wiring with line and load side terminals. It comes standard with 1 meter pigtail terminals for mounting internal accessories.

The 140G-G2C3-C15 circuit breaker is DIN rail mounted and is rated IP 20 or IP 40.

The 140G-G2C3-C15 circuit breaker is calibrated for an ambient enclosure temperature of 40 degrees Celsius and can be stored over a temperature range of -40 to 80 degrees Celsius.

The 140G-G2C3-C15 circuit breaker weighs approximately 1.1 kg and has overall dimensions of 76 x 70 x 130 mm.
February 27, 2025 BY
IN Parker

Parker AC15 Compact AC Drives

SIMPLE:.

Utilizes the free Parker DSELite software tool.

Easy Ribbon Matching – On-board Ethernet port for programming and Modbus TCPIP communication.

Clear intuitive keypad for local setup and control

-Conformal coating as standard for protection from harsh environments -Proven power stage design and technology -Replaceable fans

Safe torque-off: SIL2, PLd

SD card slot for application backup Applications: Conveyors

Conveyors

Fans

Racking machines

Packaging machines

Textile machines

Strapping machines

Labeling machine

Industrial washing machines

Machine tool spindles

Roller shutters

Technical Specifications.

Power range 0.37kW-30kW

Voltage range 230-480VAC

Dedicated thermistor input terminals

3 analog outputs, 2 analog inputs, 8 digital inputs, 2 digital outputs + 1 relay output

Leakage current:>10 mA (all models)

Product enclosure rating: IP20 (Europe)

Maximum switching frequency:10kHZ

Output frequency:0…. .590 HZ

Operating humidity: 85% relative humidity max. at 40°C, non-condensingAtmosphere: non-flammable, non-corrosive, non-toxic, dust-free

Atmosphere: non-flammable, non-corrosive, dust-free Standards: -Overvoltage category: overvoltage, overvoltage, overvoltage, overvoltage-Overvoltage category: Overvoltage category Kawasaki (number defining the shock tolerance level) Pollution level: P dilution level Kawasaki
February 27, 2025 BY
IN GE

GE Fanuc General Electric Components IC670GBI001 Bus Interface

The GE Fanuc IC670GBI001 bus interface is for the Field Control Series IC670. IC670G, IC670GB, IC670GBI, and IC670GBI00 modules.

The unit has a nominal voltage rating of 115 volts AC and 125 volts DC.

About the IC670GBI001

The IC670GBI001 bus interface is a GE Fanuc component for field control devices.

GE Fanuc is a well-known producer of technology solutions for many industries, and the GE IC670GBI001 Bus Interface module is resistant to noise in industrial environments,

vibration, high and low temperatures, humidity, and other common conditions in industrial environments.The IC670GBI001 bus interface unit has a nominal voltage rating of 115 volts AC and 125 volts DC.

The input frequency range is 47 to 63 Hz. The unit’s voltage range is 90 to 135 volts AC and 105 to 150 volts DC.

The IC670GBI001 Bus Interface Module has a rated power consumption rating of 115 volt-amperes (**value) at 48 volts AC at full load.

The power consumption rating at 24 volts AC at full load is 125 watts (**value). The unit has a hold-up time of 20 milliseconds and a power supply output voltage of 6.5 volts DC.

The IC670GBI002 Bus Interface Module works well with other components such as the Bus Interface Unit power supply and Bus Interface Unit terminal blocks.

The IC670GBI001 module has a high-quality housing made of aluminum and includes LED indicators for status updates as well as an HHM connector for handheld displays.

The IC670GBI001 bus interface unit has a logic power supply and its configuration file is stored in the memory of the terminal block.

The four included indicators are the “PWR”, “OK”, “Run” and “Bus B” LEDs. The LEDs indicate the normal operation of the module and the communication status with the CPU.

Since the IC670GBI002 unit can be used with a DC power supply, the backplane current may be limited by the lower input voltage.
February 27, 2025 BY
IN GE

GE Fanuc General Electric IC200ALG328 Output Module

About the IC200ALG328

The IC200ALG328 module is a Versamax I/O module designed and manufactured by GE Fanuc Automation.

This particular module provides 12 outputs. These outputs are analog current source type outputs.

They can operate over a current range of 4 to 20 milliamps. The module has 20.38 mA per channel to drive the output loads.

The channels of the GE Fanuc Automation IC200ALG328 Versamax I/O module can be used with the IC200ALG326 Versamax I/O module.

The channels of the IC200ALG326 module can be scaled using the IC200ALG326 module because they are similar and compatible.

The module is also compatible with Ethernet, Genius, Profibus, and DeviceNet firmware. It is also compatible with PLC CPU firmware and VersaPro software.

The GE Fanuc Automation IC200ALG328 Versamax I/O module has a thermal derating only when used at 30 volts DC and placed in a specific location on the DIN rail.

This derating is also dependent on the ambient air temperature present.GE Fanuc Automation IC200ALG328 Versamax I/O Modules are rated for 18 to 30 volts DC.

The current draw is rated at 2 amps inrush current, and the power consumption is rated at 100 milliamps without load and 12 milliamps at full scale using all 270 outputs.

The module has a 13-bit resolution with an accuracy rating of up to 1%. The module is equipped with 2 LEDs and a diagnostic tool.

It can be hot-plugged, but this needs to be done carefully to retain all components in the rack and module.

The IC200ALG328 is a 12-channel, 13-bit current analog output module designed for the GE Fanuc Versamax family.

The IC200ALG328 has a default output range, but the output range can be easily changed with jumpers.

All outputs require external power, and the IC200ALG328 module will be intelligently processed by the CPU or Network Interface Unit.

If the backplane power or communication is interrupted, or if the PLC stops running, the outputs of the IC200ALG328 module can be easily kept in their last state, or in their default state via jumpers.

The backplane must send different output data to the module or the outputs will remain in their default or previous state.
February 27, 2025 BY
IN Mitsubishi Power

Steam Power Plants

Mitsubishi Power designs and delivers highly efficient and environmentally friendly power generation facilities, including boilers, steam turbines, generators, air quality control systems, and other auxiliaries.

A steam power plant consists of a boiler, steam turbine and generator, and other auxiliaries. The boiler generates steam at high pressure and high temperature. The steam turbine converts the heat energy of steam into mechanical energy. The generator then converts the mechanical energy into electric power.

Our highly efficient and environmental friendly power plants will contribute to the stable supply of electrical power and reduction of environmental impact.

Large Capacity Power Plants

Applying ultra-supercritical pressure technology for highly efficient power generation

Our highly efficient and environmentally friendly power plants have an impressive track record in field of supercritical and ultra-supercritical pressure power plants and high level of trust in the market. We will contribute to the stable supply of electric power and to the reduction of environmental impact all around the world, based on our advanced technologies.

What is ultra-supercritical pressure?

Under normal atmospheric pressure [0.101 MPa], water boils at 100ºC. As pressure increases, the boiling temperature of water also increases. When the pressure is increased to 22.12 MPa, and at a temperature of 374ºC, water does not boil but is directly converted into steam. This is called the critical point, and the pressure above this critical point is called supercritical pressure. Supercritical pressure with a temperature equal to or more than 593ºC is called ultra-supercritical pressure.
February 27, 2025 BY
IN Mitsubishi Power

Gas Turbine Combined Cycle (GTCC) Power Plants

World-class Power Generation Efficiency

At Least 64% (LHV)

Wide Output Range

30 to 1332 MW Class

Combined Cycle Power Plants

On Grid Facility for Verification Testing

CO2 Emissions Compared with Those of Conventional Coal-fired Thermal Power Generation

About 50% Lower

High efficiency energy through combined cycle power generation

Gas turbine combined cycle (GTCC) power plants use natural gas to deliver the cleanest and highest efficiency power generation.

Plants employing state-of-the-art gas turbines of Mitsubishi Power have a 20% higher power generation efficiency than conventional coal-fired thermal power generation systems and the world’s highest level of efficiency of more than 64%. That enables CO2 emissions an approximate 50% reduction.

What is GTCC?

In the power generation method characterized by the standalone operation of a gas turbine, known as the simple or open cycle, releases exhaust gas at temperatures of around 600℃ into the atmosphere.

Combined cycle power generation improves the general thermal efficiency of the plant by recovering this high temperature exhaust gas. Many combined cycle power generation plants adopt a waste heat recovery cycle in which exhaust gas from the gas turbine is led to the waste heat recovery boiler to generate steam using recovered heat to drive the steam turbine.

Advantages and Features that Make the GTCC the Mainstream for New Thermal Power Generation Facilities

High level of thermal efficiency

In comparison with thermal efficiency of about 40% in steam power generation, combined cycle power generation features a thermal efficiency of at least 60% (with both figures on the lower heating value basis).
February 26, 2025 BY
IN Mitsubishi Power

Overview and Verification Status of T-Point 2 Demonstration Facility Gas Turbines

Purposes of the T-Point 2

To validate gas turbine technologies newly applied to achieve higher efficiency, allow operations at elevated temperatures, and reduce NOx.

To validate the reliability through long-term commercial operations of the highly efficient and environmentally friendly combined-cycle power generation.

Development of T-Point

The original T-Point demonstration facility began operation in 1997 with M501G (60 Hz), which was upgraded to M501J in 2010 and M501JAC in 2015 with response to the power industry’s demand for large-scale, high-efficiency power generation.

Since the original T-Point can not satisfy the further requirement for larger capacity and higher efficiency, we made a decision to build T-Point 2.

T-Point 2 entered full commercial operation with an enhanced JAC gas turbine from July 2020.Validation of Next Generation

Combined Cycle Power Generation

With its combination of gas turbine and steam turbine,T-Point 2 is cutting edge combined cycle power plant validation facility.

By developing next-generation technologies and validating them in T-Point 2 GTCC facilities, Mitsubishi Power helps its customers world-wide attain a stable electricity supply.

Long term demonstration of off-site plant control at T-Point 2 is conducted from the Mitsubishi Power Takasago TOMONI HUB (Analytics and Performance Center). Validation operations are run to increase the reliability of the entire plant including the main equipment such as turbines as well as auxiliary equipment such as pumps and fans. In addition, various applications of a suite of intelligent solutions TOMONI™ that serve to shorten start-up time and automatically optimize operation parameters are installed in T-Point 2. Mitsubishi Power will also be training its AI applications, allowing T-Point 2 to eventually become the world’s first autonomous combined cycle power plant.

Menu

Search for products

Back to Top
Product has been added to your cart