Category: Motorola

MPC60x 32-bit class microprocessor

L1 Cache-16KB/16KB MPC603 or 32KB/32KB MPC604

128MB of onboard ECC DRAM

Up to 1MB of embedded Flash for on-board firmware or user-specified requirements

4MB on-board flash for user-specified requirements

On-board debug monitor with self-testing diagnostic features

Two 32/64-bit PMC expansion slots with dcs-sis.com front panel and P2V/0

64-bit PCI expansion mezzanine connector

8Kx8 NVRAM and full-time clock with replaceable battery backup

One asynchronous serial debug port

Four 32-bit timers, one 16-bit timer, one watchdog timer

10/100Mb/s Ethernet transceiver interface

4-level request program, 7-level interrupter, and 7-level interrupt handler for VMEbus

IEEE P1386.1-compliant PMC slot

The MVME2300 has dual PMC ports with front panel and P2 I/O support.

The P2 I/O-based PMC follows the PMC committee recommendations for PCI I/O when using the VME64 expansion connector, and its pin-outs are compatible with the MVME2300.

In addition to providing high-performance expansion I/O, the IEEE P1386.1-compliant PMC port provides a common architecture for future generations of products.

Simply replace the PMC to meet changing I/O needs while reusing the same base platform, reducing long-term cost of ownership.

VME64 Expansion Connector

To maximize the performance of the MVME2300. five rows of 160-pin DIN connectors replace the three rows of 96-pin connectors historically used on VME P1 and P2.

Two additional rows (Z and D) have been added to the VME P1/J1 and P2/J2 connectors to provide additional I/O for the user.

The VME64 expansion connector is fully backwards compatible with existing VME card systems.

PowerPlus Architecture

The PowerPlus Architecture is a processor and bus architecture fully optimized for use from the PowerPC architecture microprocessor family,

The PowerPlus Architecture is a processor and bus architecture that is fully optimized for maximum performance from the PowerPC architecture microprocessor family, PCI bus and VME bus. The outstanding performance of VME processor boards based on the PowerPlus architecture is not due to a single factor.

The processor memory subsystem, the high-speed local bus, the optimized decoupling architecture, the decoupling of the processor from PCI, and the advanced VME bus that reduces PCI latency.

A number of design factors, such as the processor memory subsystem, optimal decoupling architecture, decoupling of the processor from PCI, and advanced VME interfaces that reduce PCI latency, all contribute to the outstanding performance.

Features

The MVME147S features include

MC68030 microprocessor

Floating point coprocessor (MC68882)

Shared DRAM with parity (no parity on MVME147SRF)

Four serial ports with RS-232C buffers

Small Computer System Interface (SCSI) bus interface with DMA channel

Timer/calendar with battery backup

2K by 8 CMOS RAM with battery backup

Four ROM/PROM/EPROM/EPROM sockets (16-bit wide)

VMEbus interrupter

VMEbus system controller functions

VMEbus master interface (A32/D32. A24/D16 compatible)

VMEbus Requestor

SCON, DUAL, FAIL and STATUS status indicators

Reset and abort switches

Centronics Printer Port

Two 16-bit ticking timers for periodic interrupts

Watchdog timer

Ethernet transceiver interface (except MVME147SRF)

Cooling Requirements

Motorola VME modules are specified, designed, and tested to operate with forced air cooling from

Reliable operation over the incoming air temperature range of 0 degrees Celsius to 55 degrees Celsius (32 degrees Fahrenheit to 131 degrees Fahrenheit).

Temperature qualification was performed in a standard Motorola VMEsystem 1000 chassis.

A 25-watt load board was inserted in two card slots, one dcs-sis.com on each side, adjacent to the board under test to simulate a high power density system configuration.

Three axial fans, each rated at 100 CFM, were mounted directly below the MVME card box.

The temperature of the incoming airflow was measured between the fan assembly and the card box, where the airflow first encountered the module under test.

The test software is executed when the module is subjected to a change in ambient temperature. The test software is executed when the ambient temperature changes.

Case temperatures of critical high power density integrated circuits are monitored to ensure that component supplier specifications are not exceeded.

While the exact amount of airflow required for cooling depends on the ambient air temperature as well as the type, number, and location of boards and other heat sources.

However, typically as little as 10 CFM of airflow through the module is sufficient for cooling.

♦ 25 MHz MC68040 with floating point co-processor or 25 MHz MC68LC040

♦ High-performance DMA, supports VMEbus D64 and local bus memory burst cycles

♦ 16 or 32MB of configurable SDRAM with ECC option 

♦ 128KB of SRAM with battery backup

♦ 1MB of Flash memory

♦ 8K x 8 NVRAM and time-of-day clock with battery backup 

♦ Four serial communication ports, configured as EIA-232-D DTE 

♦ Two 16-bit or one 32-bit IndustryPack®dcs-sis.com ports with one DMA channel per port

♦ Six 32-bit timers, one watchdog timer 

♦ Optional SCSI and Ethernet interfaces 

♦ Two 32-pin JEDEC DIP sockets for EPROM

♦ Remote Reset/Abort/Status control functions 

♦ On-board debugger and diagnostic firmware

Dual IndustryPack logic interface for embedded monitoring and control applications

The MVME162P2 embedded controller provides a powerful and functional processor which can be customer-configured for specific applications.

The MVME162P2 extends its range of solutions by boosting the performance level and increasing the number of options. This flexibility allows a user to configure cost-ffective solutions ranging from embedded controllers to single-board computers. With the compute power of the MC68040 and the flexibility of the IndustryPack mezzanine interface, the MVME162P2 combines the mechanical ruggedness of VME with the cost effectiveness of PC-type products.

The inclusion of the new “Petra” application-specific integrated circuit (ASIC), which replaces functions formerly implemented in the IP2 chip and MC2 chip, improves the performance of the memory subsystem. Memory configuration switches enable the customer to tailor memory size for applications requiring smaller memory configurations.

IndustryPack Interface

A key feature of the MVME162P2 is the IndustryPack interface. IndustryPack modules provide a wide variety of connectivity to “real-world” I/O. Expansion is accomplished by 

means of a mezzanine board mounted to the MVME162P2. 

Up to two single-wide IndustryPack modules can be installed on the MVME162P2 and still occupy only one VME slot.

• 8 channels

• 16-bit DACs

• Fast settling: 10 µs maximum to ±0.003 percent of FSR

• Buffered voltage output (±10 V at 5 mA)

• Multiplexed programmable outputs on P2 connector for testing analog outputs

• Double-buffered data latches

• Jumper-selectable synchronized update control

• Selectable external update control input or software-controlled strobe provides single update strobe for all DAC outputs

• Front panel fail LED

• High reliability DIN-type output connector

• Outputs set to 0.0 V on power up

— Outputs are automatically disconnected from the field at power up

• Double Eurocard form factor

• Supports VMIC’s analog expansion and Built-in-Test bus (AMXbus™) that interconnects the P2 connectors of various VMIC ADC and DAC boards and expansion multiplexer boards

• Multiplexed programmable outputs for testing analog input multiplexer boards

— Requires VMIC ADC board and AMXbus for Built-In-Test

INTRODUCTION — The VMIVME-4116 

Digital-to-Analog Converter (DAC) Board performs digital-to-analog conversion on 16-bit positive true offset binary or two’s complement coded words, with an analog output range of -10 to +10 V. This provides for a resolution of 305 µV for each digital input of 1 LSB change. The buffered output voltage settles to within 1/2 LSB in 10 µs.

The DAC offers a Digital-to-Analog Integrated Circuit (IC) per channel. A Control and Status Register (CSR) is loaded by the processor and this register controls the functioning of the board. The CSR can be read by the processor at any time. The VMIVME-4116 dcs-sis.com board functional block diagram is shown in Figure 1. Each of the eight DACs is preceded by double-buffered data latches. 

The data latches allow versatility in the way the DAC analog output may be updated.

There are three methods by which new data can be converted by a DAC. Each method is enabled/disabled by on-board jumpers and is further controlled by a CSR that must be loaded by the user.

FUNCTIONAL CHARACTERISTICS

Compatibility: The VMIVME-4116 Analog Output Board is a standard, double height, printed circuit board which is compatible with the VMEbus specification.

Board Address: The physical address for the board is selected by 12 DIP switches. VMEbus address lines A05 through A15 are decoded for board selection.

VMEbus Access: Address modifier bits are jumper-selectable to support nonprivileged short I/O or supervisory short I/O access. The board is factory configured for supervisory short I/O access. 

Data Transfer: Data can be written to one of the eight Digital-to-Analog Converters (DACs) in bytes or words (via data bits D00 through D15). Bipolar operation(-10 to +10 V output) uses offset binary coding or two’s complement binary coding.

INTRODUCTION — 

The VMIVME-7452 is a passive board that holds one floppy and one hard drive with an optional Flash drive available.

The board is a 6U VMEbus form factor, deriving its power from the standard VMEbus P1 and P2.

The VMIVME-7452 has been designed to interface to dcs-sis.com VMIC’s line of VMEbus-compatible PC/AT SBC boards. 

These SBC boards incorporate the floppy and IDE controllers on-board. Refer to the compatible SBC list in this specification.

SPECIFICATIONS

Physical Dimensions: Standard VME double height Eurocard (one slot)

160 x 233.25 x 20.32 mm

User Connectors: 34-pin floppy drive 40-pin IDE

Ambient Temperature:

All Disks: 5 to 50 ˚C, operating

Storage: -25 to 60 ˚C

Rate: 20 ˚C per hr maximum

Humidity: 20 to 80 percent, noncondensing, maximum 

wet bulb 29 ˚C

Hard Drive Access Time:

Average Access Time: 14 ms

Average Latency: 6.67 ms

Power Requirements:

+5 V, 2.5 A maximum (spinup)

<1.0 A typical

Flash Drive System Performance:

Data Transfer Rate to Flash: 4.0 Mbyte/s burst

Data Transfer Rate from Flash: 6.0 Mbyte/s burst

Sleep to Write: 2.5 ms maximum

Sleep to Read: 2.0 ms maximum

Reset to Ready: 50 ms, typical, 400 ms, maximum

Flash Drive System Performance:

DC Input Voltage (Commercial): 5 V ±10%, 

3.3 V ±5%

Power Consumption:

Sleep: 200 µA at 3.3 V, 500 µA at 5.0 V

Read: 32 to 80 mA at 3.3 V, 46 to 120 mA at 5.0 V

Write: 32 to 80 mA at 3.3 V, 46 to 120 mA at 5.0 V

Compatible SBC Boards:

VMIVME-7591 VMIVME-7698

VMIVME-7592 VMIVME-7740

VMIVME-7695 VMIVME-7750

VMIVME-7697 VMIVME-7751

VMIVME-7697A VMIVME-7765

Functional Features:

16. 25 or 33.33 MHz MC68030 Enhanced 32-bit Microprocessor

16. 25 or 33.33 MHz MC68882 Floating Point Co-Processor

4. 8. 16 or 32MB of shared DRAM with programmable parity

4K x 8 SRAM and timing clock with battery backup

Four 28/32-pin ROM/PROM/EPROM/EPROM sockets, 16-bit wide

A32/D32 VMEbus master/slave interface with system controller function

Four EIA-232-D serial communication ports

Centronics compatible printer port

Two 16-bit timers and watchdog timer

SCSI bus interface with DMA

Ethernet transceiver interface

4-level requester, 7-level interruptor and 7-level interrupt handler for VMEbus

On-board debugger and diagnostic firmware

VMEbus single board computers without dcs-sis.com additional backplane modules

The MVME147 series is a family of VMEbus single board computers.

The on-board resources and peripheral controllers eliminate the need for additional modules on the VMEbus backplane, reducing costs and freeing up valuable bus slots for other functions.

The MVME147 series utilizes the MC68030 enhanced 32-bit microprocessor.

The MC68030 is the first general-purpose microprocessor to provide on-chip cache memory for instructions and data, increasing processor efficiency by 20 to 40 percent.

The MC68030 has a full Memory Management Unit (MMU) that provides software protection and virtual memory functions critical to many applications.

Functional Features:

Processor options: 60 MHz MC68060 enhanced 32-bit microprocessor with 16KB cache, MMU and FPU;

or 64 MHz MC68LC060 enhanced 32-bit microprocessor with 16KB cache and MMU

A32/D64 VMEbus master/slave interface with system controller functionality

16MB Configurable SDRAM

512KB SRAM with Battery Backup

2MB Flash for on-board monitor/debugger or user-installed firmware

8K x 8 NVRAM and time clock with battery backup

Two serial communication ports, EIA-232-D DCE for console port, second port

User configurable to EIA-232-D/EIA-422 (V.36) DTE/DCE

Four 16-bit or two 32-bit IndustryPack® ports, dcs-sis.com one DMA channel per port

Six 32-bit timers, one watchdog timer

Optional SCSI and Ethernet interfaces

One 32-pin JEDEC socket for EPROMs

Four-slot IndustryPack logic interface for embedded monitoring applications

The MVME172P4 allows users of VME embedded controllers to realize the price/performance ratio of the RISC architecture while maintaining the MC68000 target code.

while maintaining MC68000 target code compatibility.

By combining the superscalar performance of the MC68060 with a wide range of optional features and the IndustryPack interface, OEMs can customize the MC68060 for their applications.

OEMs can choose the right product for their application without having to pay for features they don’t need.

The new “Petra” application-specific integrated circuits (ASICs) replace features previously implemented in the IP2 chip, MC2 chip, and MCECC chip, improving the performance of the memory subsystem.

Memory configuration switches enable customers to customize memory sizes for applications requiring smaller memory configurations.

The MVME2700 Series is a family of VME processor modules based on Motorola’s PowerPlus VME architecture and PowerPC® microprocessors.

The MVME2700’s flexibility provides an excellent base platform that can be quickly customized for a variety of industry-specific applications.

The flexibility of the MVME2700 provides an excellent base platform that can be quickly and easily customized for a variety of industry-specific applications.

Designed to meet military, aerospace, industrial automation and medical needs, the MVME2700 is suitable for a wide range of applications.

The DRAM expansion mezzanine allows memory upgrades to up to 256MB of ECC DRAM without the need for additional VME slots.

MVME2700 Details

PCI Expansion

The MVME2700 module has 64-bit PCI connectivity to support PCI expansion carriers such as Motorola PMCspan.

Consult your local Motorola representative for design details on connectors and electrical specifications.

Memory Modules

The MVME2700 series utilizes a modular memory design. Mezzanine arrays support 16MB to 256MB of additional DRAM.

These RAM200 expansion modules allow field upgrades of memory capacity and do not require additional VME slots.

Transition Modules

The MVME2700 is available in two artifact variants. dcs-sis.com One series is backward compatible with the MVME712M Transition Module I/O. The other series accepts the MVME712M Transition Module I/O. The other series accepts

The MVME761 Transition Module has additional synchronous/synchronous serial ports, 10/100BaseT interfaces, fast 16-bit SCSI, and IEEE 1284 compliant parallel ports.

MVME761

The MVME761 Transition Module provides industry standard connectors to access the IEEE 1284 parallel port via an RJ-45 connector,

10BaseT or 100BaseT ports, two DB-9 connectors for access to asynchronous serial ports configured as EIA-574 DTEs, and two HD-26 connectors for access to asynchronous serial ports configured as EIA-574 DTEs.

and two HD-26 connectors that access the synchronous/synchronous serial ports.

These serial ports are labeled Serial 3 and Serial 4 on the MVME761 faceplate.

They can be individually configured as EIA-232. EIA-530. V.35 or X.21 DCE or DTE by installing a Motorola Serial Interface Module (SIM).

The P2 adapter provides the interface module signals for the MVME761 transition module.

The 3-row P2 adapter can be used for 8-bit SCSI. 5-row P2 adapters support 16-bit SCSI and PMC input/output.

MVME712M

The MVME712M Transition Module provides industry standard connectors for the Centronics® parallel port, an AUI port, and four DB-25 connectors.

These connectors provide access to asynchronous/synchronous serial ports that can be jumper-configured to EIA-232 DCE or DTE. 3-row P2 adapters are available for 8-bit SCSI.

To access additional user-definable I/O pins available through the 5-row VME64 expansion connector, a dedicated P2 adapter board is available.

This adapter board replaces the traditional 3-row P2 adapter and extends its functionality with access to the PMC I/O pins.

The MVME712M is also available in several other different I/O and connector combinations.

Description.

The MVME712M is an I/O transition module for Motorola MPU VME Modules, VME Processor Modules, Embedded Controllers, and Single Board Computer (SBC) series processor modules.

The MVME712M is used as an interface between the processor module and its peripherals. The purpose of this module is to provide rear-panel The purpose of this module is to provide rear-panel industry-standard connectors to simplify the customer’s external cable requirements.

P2 adapter boards and cables are provided for interconnecting the MVME712M to peripheral devices. interconnecting the MVME712M to the MVMExxxx. the P2 adapter assembly transfers I/O signals and ground from the P2 connector on the chassis backplane to the MVME712M, and from the P2 adapter assembly to the MVME712M. at the VME Module MPU connection. At the VME module MPU connection, the P2 adapter assembly transfers I/O signals and ground from the P2 connector on the chassis backplane to the MVME712M.

The MVME712M routes the signals to four serial ports, which dcs-sis.com are realized through four industry standard DB-25 connectors on the MVME712M. Serial Ports. The serial ports can be configured as EIA-232-D DTE or DCE via jumpers on the MVME712M. The serial ports can be configured as EIA-232-D DTE or DCE via jumpers on the MVME712M.

The MVME712M also has an Ethernet port, a SCSI port, and a printer port on the front panel. Printer Port. In addition, the MVME712M routes EIA-232-D Port 2 signals to the internal modem. signal to the internal modem.

MVME712M Transition Module

The MVME712M features include

Four 25-pin multi-protocol EIA-232-D serial ports (via P2 adapter)

One independent printer port (via P2 adapter)

Small Computer System Interface (SCSI) shielded connector bus interface (via P2 adapter) for connecting internal and external devices

Green LED on module indicates terminator power supply

Yellow LED on module indicates transceiver power

SCSI termination resistor mounted on the socket for end-of-cable or middle-of-cable configurations

Modem interface on module

RFI protection on front panel

Electrostatic discharge (ESD) protection on front panel

P2 adapter board