Category: GE

Product Description

The DS200AAHAG1AD is an ARCNET connector board manufactured by General Electric as part of the Mark V LM SpeedtronicTurbine control system.

Mark V LM manual GEH-6353B clearly summarizes the function of the DS200AAHAG1AD in the control system. The board is referred to by its acronym AAHA.

The DS200AAHAG1AD, abbreviated AAHA, is part of the Speedtronic Mark V LM control panel.

The board is capable of providing connectivity and interface functionality between a control engine with an I/O core and external hardware.

The control engine is typically located within the core. The kernel typically requires the use of two AAHA boards.

One board is used to facilitate the stage link between the user interface and the core.

The second board is capable of connecting the core to COREBUS.

This link allows communication between the I/O core and the control engine.

The DS200AAHAG1AD is plugged in and installed to operate without any type of hardware or software modification.

The AAHA board is relatively small. It has an EBNC connection port that is not normally used.

It has one ARCBNC-B labeled P1 and one ARCBNC-A port labeled P1.

These ports are BNC ARCNET communication ports. There is an E2 and E1 LED indicator.

There is an EPL 9-pin connection that is not normally used and an APL 10-pin connection port that is used as an ARCNET communications link.

The expansion base uses a box connector. It supports output voltages in the range of 0 to 125 volts DC with nominal voltages of 5. 24. and 125 volts DC.

For the voltage range of 8 to 5 volts AC, this expansion base has a load current of 265 amps per point.

The IC200CHS212 chassis is constructed of high quality materials.The Versamax module provides high performance and is a cost-effective industrial solution.

The expansion relay has ports for connection to programmers and handheld devices.

It is designed with open architecture and should be protected from dust, dirt and contaminants. The temperature of the module should not exceed 60 degrees Celsius.

The IC200CHS212 is GE’s 16-point I/O relay expansion base. The relay is replaceable, labeled 8 amps and fused.

The VersaMax I/O Modules IC200MDL740 and MDL750 provide 24 VDC O.5A outputs to control the IC200CHS212 relays.

The IC200CHS212 dimensions (excluding DIN rail height) are 253.7 mm (9.9 in.) x 126 mm (4.95 in.) x 73 mm (2.8 in.).

Power supply modules such as the IC200CHS212 snap onto all Versamax interface units or power booster carriers.

Any power supply can be specified as the main power supply for modules in an I/O station or as an additional power supply for large I/O applications.

The IC200CHS212 and other VersaMax I/O plug-in disconnect bases enable the IC200CHS003 to connect to a variety of termination bases.

Relay bases provide more protection and higher current output. The relays are controlled by the outputs of the VersaMax I/O modules.

Users can easily disconnect each point signal from the I/O module by disconnecting the base. The module’s field terminals can also be removed.

The relays located on the plug-in terminals are intended to be controlled using a typical 24 VDC 0.5 VersaMax output module.

IC200CHS212 Technical Description

The GE IC200CHS212 base is a 16-point expansion base. It provides LED indicators for each I/O point.

The IC200ALG432 module is an analog module with mixed inputs. It is manufactured by GE Fanuc as a Versamax module.

About the IC200ALG432

The GE Fanuc IC200ALG432 module is a hybrid analog module that runs on a 10-volt DC power supply.

It is a 12-bit module equipped with 4 channels and 2 output channels.

The analog module has an update rate time of 0.4 milliseconds and an input response time of 5 milliseconds.

The analog module requires an external power supply to power the outputs. The inputs of the module are powered by the external power supply of the transceiver.

The CPU is present in the module that handles the operation. the IC200ALG432 module has LEDs on the front of the module that indicate the flow of power and backplane currents.

No thermal derating occurs in this hybrid module. the IC200ALG432 module draws a total of 160 milliamps of current during normal operation. including load current.

The diagnostic feature of the module helps to detect the loss of power on the user side.

It provides four channels and two channel outputs. The outputs require a 24V external power supply and the inputs are powered from the transceiver’s external power supply.

The CPU or NIU performs intelligent processing of the IC200ALG432 module. Includes 4 words of analog input data and 2 words of analog output data.

This IC200ALG432 uses LEDs to indicate the presence of user-side power for analog field-side circuits as well as backplane power.

The LEDs emit a green light when operating as intended. When properly installed, this module reports the loss of user-side power failure for field-side circuits and conveniently sets up jumpers for outputs.

The IC200ALG432 can be set to maintain the last state or default values even if the backplane or field power is temporarily interrupted. The module reports the loss of user-side power failures for field-side circuits.

About IC200DTX850

The IC200DTX850 terminal is a data display terminal manufactured by GE Intelligent Platforms/GE Fanuc for the GE Versamax product line.

These Versamax series data terminals, including the GE Fanuc IC200DTX850 terminal, are specifically designed for use in a variety of applications that

Including simple timer and counter applications, they can also display full text messages.

These terminals can be controlled by the user via a numeric keypad. Connecting a Versamax Nano or Micro PLC to the terminals is easy and requires no user configuration.

Because these Versamax terminals are pre-programmed, the GE Fanuc IC200DTX850 Operator Interface Terminal specifically supports up to 200 stored messages.

The GE Fanuc IC200DTX850 Data Display Terminal also has an LCD backlight for the screen.

It has a keypad with 8 keys for control functions and requires the IC200BL555 cable or equivalent to support its operator interface.

The data panel operates on an external power supply rated at 24 volts DC and 50 milliamps.

The GE Fanuc Versamax IC200DTX850 data display terminal measures approximately 182 x 101 x 37 mm.

It has an operating temperature range of 0 to 50 degrees Celsius.

The IC200DTX850 data interface terminal has an RS-232 serial port for communication purposes.

This port is designed for different commands, including serial input/output commands, Modbus RTU slave commands or SNP slave commands.

In addition, this data terminal is compatible with the Data Designer software.

The Versamax controllers compatible with this terminal are available in micro and nano models, which are small in size, while offering powerful control and a high level of performance.

Overview of GE RXI controller

GE RXI controller is a high-performance, high-reliability control system introduced by GE Intelligent Platform. It utilizes cutting-edge CPU technology, market-leading industrial Ethernet network technology, and a unique user interface to provide equipment manufacturers and end-users with the most efficient and reliable control system.

Third, the GE RXI controller parameters in detail

Processor: The GE RXI controller utilizes a high-performance dual-core CPU to ensure efficient system operation.

Memory: The RXi Box IPC has 4G RAM memory to support high-performance designs.

Storage System: 32GB industrial-grade SSD comes standard, while an optional 250GB hard disk is provided to ensure safe data storage.

Network Interface: Supports Gigabit PROFINET (with built-in MRP redundancy) and Ethernet ports to provide high-speed data transfer capability.

Wireless communication: Optional WLAN function enables wireless communication through the internal Mini PCIe card holder.

Serial communication: RS-232 port (RJ-45) is provided to support serial communication needs.

Video/Graphic Interface: VGA port is supported for resolutions up to 2560×1440 @60Hz.

Audio: Provides micro DIN audio socket via IFP.

USB Interface: Provides two USB 2.0 standard ports for easy connection of external devices.

IV. Features of GE RXI Controller

Unique Intelligent Display Module: Provides configuration and maintenance functions for the controller without the need for additional software for easy operation.

High-performance control: Ensures efficient system operation through technologies such as high-performance dual-core CPU and Gigabit PROFINET.

Compact form factor: PROFINET-based design provides a small form factor solution for equipment manufacturers and *end users.

Highly Flexible Distributed I/O Functionality: Supports a variety of expansion slots to meet a wide range of industrial automation needs.

High Reliability: Adoption of industrial temperature grade components, combined with patented thermal monitoring technology and advanced passive cooling technology, ensures reliable operation in harsh environments.

About the IC200ERM002

The GE Fanuc IC200ERM002 module is a non-isolated expansion receiver module that is part of the Versamax family.

This expansion module is used to enhance the functionality of a Versamax PLC or I/O output station and also increases the number of modules that can be connected.

The IC200ERM002 Expansion Module has a **capacity of 7 racks with up to 8 modules per rack*.

It requires an installed power supply to power all connected devices.

When an additional power supply or booster carrier is used, it should be connected to the mains power supply on the IC200ERM002 Expansion Module.

It also features 3 on-board LEDs to indicate the operational status of the device.

The module can also be used as a single-ended or multi-rack Versamax I/O expansion system.

Where the module is used in a multi-rack implementation, the total cable length cannot exceed 50 feet or 15 meters.

When the Versamax GE Fanuc IC200ERM002 Non-Isolated Expansion Receiver Module is used in a single-ended system with only 1 expansion rack, the

The cable length should not exceed 3.3 feet or 1 meter.

It has a data rate of 2.765 Mbps or 5 Mbps, depending on the implementation used.

The GE Fanuc IC200ERM002 expansion module is equipped with two 26-pin D-shell expansion female ports.

In addition, it has two different current consumption ratings with a 3.3 volt or 5 volt backplane rating.

When the backplane voltage is 5 volts, the current consumption is rated at 70 milliamps and when the backplane voltage is rated at 20.3 volts, the current consumption is rated at 3 milliamps.

About the IC200MDD841

The IC200MDD841 module is a high-speed counter module manufactured by GE Fanuc.

It is part of the Versamax series and has mixed discrete inputs and outputs, including 12 positive logic outputs and 20 positive logic inputs, some of which are configurable.

Devices connected to these I/O connectors have two states: on and off.

The GE Fanuc IC2MDD200 module has no protection features, such as internal fuses or isolation of individual channels.

It supports a variety of input and output configuration settings, such as pulse-width modulation, ramp pulse train, pulse train, and high-speed counters.

When this module is set to its default configuration, it has 841 Type A high-speed counter outputs and inputs.

These high-speed counters process pulse signals at 4 kHz. In addition, in the default configuration, the module has 80 standard outputs and 8 standard inputs.

The backplane powers the GE Fanuc IC200MDD841 high-speed counter module, but a separate power supply powers all external output devices.

When the module is connected to a backplane power supply rated at 5 volts, it draws 30 milliamps of current.

The inputs and outputs of the IC200MDD841 module operate at 24 volts DC.

The module’s on/off state current ratings are 3 to 8 mA/0 to 0.5 mA, respectively.

It measures 66.8 mm or 2.63 inches long, 110 mm or 4.3 inches wide, and 50 mm or 1.956 inches deep.

The high-speed counter module provides error detection and displays up to 13 words of status data.

It has on-board LEDs that display device status information.

The IC200ALG630 has a backplane current consumption of 3 mA at the 125 VDC and 5.3 VDC outputs on the backplane.

It is also rated for optical and frame-to-ground isolation with a continuous voltage duration of 250 VAC and a 1500 VAC voltage duration of 1 minute.

The module also provides LED status indicators, specifically an OK LED that indicates active backplane power when the module fails, and amber when lit green.

The IC200ALG630 module is GE’s 16-bit analog input module. It is an industrial module designed to handle a wide range of application requirements.

It comes with a 7-bit thermocouple with 16 channels. This thermocouple analog input module receives power from the backplane power supply.

It offers four cold end compensation options, no cold end, remote cold end, fixed cold end, and localized cold end compensation.

It is rated at 5 volts DC. It supports different thermocouples of type J, K, T, S and R.

The IC200ALG630 module is capable of drawing a total of 5 milliamps of current from the 125 volt bus.

The update rate of the analog module is 60 milliseconds for 60 Hz and 50 milliseconds for 70 Hz.

An OK indicator on the front of the module indicates the presence of backplane power.

The IC200ALG630 module has a compact design that saves panel space.

It measures 4.3 inches wide, 2.63 inches high, and 1.95 inches deep.

The temperature range should be set between 0 and 60 degrees Celsius. The thermocouple module has advanced diagnostic features.

It can issue channel-specific alarm reports. It can also detect over- and under-range conditions in the input.

Faults caused by thermistors can be easily detected by the module as internal faults. The module has not experienced thermal derating.

The GE Fanuc IC670GBI001 bus interface is for the Field Control Series IC670. IC670G, IC670GB, IC670GBI, and IC670GBI00 modules.

The unit has a nominal voltage rating of 115 volts AC and 125 volts DC.

About the IC670GBI001

The IC670GBI001 bus interface is a GE Fanuc component for field control devices.

GE Fanuc is a well-known producer of technology solutions for many industries, and the GE IC670GBI001 Bus Interface module is resistant to noise in industrial environments,

vibration, high and low temperatures, humidity, and other common conditions in industrial environments.The IC670GBI001 bus interface unit has a nominal voltage rating of 115 volts AC and 125 volts DC.

The input frequency range is 47 to 63 Hz. The unit’s voltage range is 90 to 135 volts AC and 105 to 150 volts DC.

The IC670GBI001 Bus Interface Module has a rated power consumption rating of 115 volt-amperes (**value) at 48 volts AC at full load.

The power consumption rating at 24 volts AC at full load is 125 watts (**value). The unit has a hold-up time of 20 milliseconds and a power supply output voltage of 6.5 volts DC.

The IC670GBI002 Bus Interface Module works well with other components such as the Bus Interface Unit power supply and Bus Interface Unit terminal blocks.

The IC670GBI001 module has a high-quality housing made of aluminum and includes LED indicators for status updates as well as an HHM connector for handheld displays.

The IC670GBI001 bus interface unit has a logic power supply and its configuration file is stored in the memory of the terminal block.

The four included indicators are the “PWR”, “OK”, “Run” and “Bus B” LEDs. The LEDs indicate the normal operation of the module and the communication status with the CPU.

Since the IC670GBI002 unit can be used with a DC power supply, the backplane current may be limited by the lower input voltage.

About the IC200ALG328

The IC200ALG328 module is a Versamax I/O module designed and manufactured by GE Fanuc Automation.

This particular module provides 12 outputs. These outputs are analog current source type outputs.

They can operate over a current range of 4 to 20 milliamps. The module has 20.38 mA per channel to drive the output loads.

The channels of the GE Fanuc Automation IC200ALG328 Versamax I/O module can be used with the IC200ALG326 Versamax I/O module.

The channels of the IC200ALG326 module can be scaled using the IC200ALG326 module because they are similar and compatible.

The module is also compatible with Ethernet, Genius, Profibus, and DeviceNet firmware. It is also compatible with PLC CPU firmware and VersaPro software.

The GE Fanuc Automation IC200ALG328 Versamax I/O module has a thermal derating only when used at 30 volts DC and placed in a specific location on the DIN rail.

This derating is also dependent on the ambient air temperature present.GE Fanuc Automation IC200ALG328 Versamax I/O Modules are rated for 18 to 30 volts DC.

The current draw is rated at 2 amps inrush current, and the power consumption is rated at 100 milliamps without load and 12 milliamps at full scale using all 270 outputs.

The module has a 13-bit resolution with an accuracy rating of up to 1%. The module is equipped with 2 LEDs and a diagnostic tool.

It can be hot-plugged, but this needs to be done carefully to retain all components in the rack and module.

The IC200ALG328 is a 12-channel, 13-bit current analog output module designed for the GE Fanuc Versamax family.

The IC200ALG328 has a default output range, but the output range can be easily changed with jumpers.

All outputs require external power, and the IC200ALG328 module will be intelligently processed by the CPU or Network Interface Unit.

If the backplane power or communication is interrupted, or if the PLC stops running, the outputs of the IC200ALG328 module can be easily kept in their last state, or in their default state via jumpers.

The backplane must send different output data to the module or the outputs will remain in their default or previous state.