Category: GE

About the DS200TCEAG1B

This DS200TCEAG1B printed circuit board or PCB for short was originally developed to exist as an Emergency Overspeed Board within the greater Mark V Turbine Control System Series. The Mark V Series is one of the more recent additions to the slew of Mark-named product series offered with General Electric Speedtronic technology, and specifically applies to wind, steam, or gas turbine control systems and automated drive assemblies. This DS200TCEAG1B printed circuit board is not the original Emergency Overspeed Board that was manufactured by General Electric for placement in their Mark V Turbine Control System Series; that would be the similarly-named DS200TCEAG1 printed circuit board notably missing this DS200TCEAG1B product offering’s singular B-rated functional product revision.

Hardware Tips and Specifications

This DS200TCEAG1B Emergency Overspeed Board has its own particular set of hardware component inclusions and specifications, as revealed in original Mark V Series instructional manual documentation. The General Electric Emergency Overspeed Board model DS200TCEAG1B features one microprocessor and multiple programmable read only memory (PROM) modules. It also contains 3 fuses, 30 jumpers, and a pair of bayonet connectors. The DS200TCEAG1B board monitors the Mark V Series drive for over speed and flame detection trip conditions and shuts down the drive as appropriate. The bayonet connectors in the assembly of this DS200TCEAG1B Emergency Overspeed Board are used to connect the board to other devices and boards in the drive; these male bayonet connectors on the end of the cables require some consideration before you connect them to the female connectors on the board, as detailed in depth in GE instructional manual materials. To remove a bayonet connector, hold the connector with one hand and with the other hand secure the board to keep it from bending or moving. Pull the bayonet connector out of the female connector on the board and put the cable aside until you are ready to connect it to the replacement board.

Several specific connectors and integrated circuits are incorporated into the assembly of this TCEA-abbreviated PCB. This DS200TCEAG1B Mark V Series printed circuit board’s circuits are tasked with various diagnostic functions relating to this DS200TCEAG1B PCB’s greater overspeed processing functionality. Some of these integrated circuits include the TCEA Flame Detection Circuits, the TCEA Turbine Overspeed Circuit, and the TCEA Automatic Synchronizing Circuit. Each of these circuits has been named in terms of their functionality to the greater DS200TCEAG1B printed circuit board and Mark V Series automated drive assembly.

Intuitive transformer protection

The Multiline™ 345 is a member of the Multilin 3 series of protective relay platforms designed for the protection, control and management of power transformers as primary or standby protection.

The Multiline™ 345 provides advanced transformer protection, control and monitoring in an economical withdrawable or non-withdrawable design.

The 345 contains a full range of independent protection and control elements as well as advanced communications, metering, monitoring and diagnostics.

Key Benefits

-Safe, high-speed protection with improved energisation suppression

-Field-proven algorithms and reliable protection against unintentional tripping or inadequate protection

-Integrated transformer thermal monitoring for asset management maintenance optimisation

-Earth current monitoring sensitive earth fault protection for detecting 5% of earth fault windings

-Temperature monitoring via remote RTDs using RMIO modules supporting up to 12 RTDs

Easy to use and flexible with one-step setup, universal CT inputs and assignable CT inputs

-Flexible communications with multiple ports and protocols for seamless integration

-Strong security and hierarchical password control for centralised management

Pull-out design simplifies testing, commissioning and maintenance for increased process uptime

-Application flexibility with programmable logic elements

-Switchgear diagnostics and simple troubleshooting output test modes via trip/close circuit monitoring and LEDs and digits

-Environmental monitoring system for monitoring operating conditions and planning preventive maintenance

-Rugged design that exceeds industry standards with automotive-grade components and advanced test procedures such as accelerated life cycle testing

-Available in pull-out or non-withdraw-out options

-Simplifies migration of legacy MII Series relays to Series 3 platforms

-Intuitive configuration software and user-friendly logic configuration tools

This digital relay shall be capable of providing motor protection and management functions.

Its main protection function shall be thermal modelling, which consists of the following 4 main components:

– Overload curve

– Negative sequence unbalance/single phase offset

– RTD offset (hot/cold motor compensation)

– Motor cooling time constant

Special attention should be paid to the protection of the rotor during stall and acceleration. If the rotor is to be protected during stall and acceleration, the

The stall/acceleration curve must be voltage compensated and must be equipped with a speed switch input.

The stator protection thermal model should combine positive and negative sequence currents and RTD winding feedback inputs.

This allows the model to be dynamic at all times, thus allowing the motor load and temperature to be tracked.

The protection functions should include:

– Stall

– Mechanical blocking

– 12 RTD inputs

– Ground overcurrent

– Short circuit

– Differential protection (using CT inputs from both ends of the motor winding (6))

– Voltage transformer input (to provide over-voltage, under-voltage, reverse-phase, over-frequency and under-frequency functions)

The motor management relay shall be fully equipped for power measurement. The event log shall be capable of storing the last 40 events.

It shall be capable of storing 16 cycles of waveform data for each trip occurrence. The relay shall be equipped with an analogue function which is used to test the relay.

The user interface includes:

– A 40 byte vacuum phosphor screen and keypad for access to actual and set values.

– An RS232 port on the front panel for programming the set values.

– an RS485 port using open protocol (selectable baud rate up to 19.200 bps)

– A separate auxiliary RS485 port for increased security or for the exclusive use of maintenance personnel.

– The interface software should be in Windows® format

The relays are of extractable construction for easy testing, maintenance and replacement of parts.

These instructions are not intended to cover all details or variations in the equipment, nor do they provide whether installation, operation or maintenance requires further information or presents special problems

For the buyer, those not adequately covered shall refer to General Electric Company.

To the extent required, the products described herein comply with applicable ANSI, IEEE, and NEMA standards; however, with respect to local codes and ordinances, as they vary widely.

The 745 Transformer Protection System™ is a high-speed, multiprocessor-based three-phase, two-winding or three-winding transformer management relay.

for the protection and management of primary small, medium and large power transformers.

The 745 combines percentage differential, overcurrent, frequency and overexcitation protection elements as well as individual harmonic and total harmonic distortion (THD) monitoring in one economical package.

The relay offers a variety of adaptive relaying functions:

-Adaptive harmonic suppression, which resolves in inflow

-Adaptive time overcurrent element, which can be based on the harmonic content of the transformer capacity calculated when supplying high load currents

-Multiple set point groups that allow the user to enter and dynamically select from up to four relay settings to address different protection requirements for power system configurations

Dynamic CT ratio mismatch correction for monitoring on-load tap positions and automatically correcting CT ratio mismatches.

FlexLogic™ which allows PLC-style equations based on logic inputs and protections to be assigned to any of the 745’s output elements.

The 745 also includes powerful test and simulation capabilities.

This allows protection designs to be based on captured or computer-generated relay operation test capability waveform data, which can be converted to a digital format and downloaded to the 745.

The 745’s analogue buffer can be used for “playback”. The recorded waveform capture feature also provides waveform data for fault, surge or alarm conditions.

The auto-configuration feature eliminates the need for any special CT connections by eliminating the need for all CTs with Y-connections.

The IC697PCM711 module is a programmable coprocessor module from GE Fanuc.

This single-slot programmable coprocessor module is part of the GE 90-70 series and has a dual-task module that can be programmed to perform different functions.

The different functions that the IC697PCM711 module can be programmed to perform include real-time calculations, operator interface functions, and data functions.

The IC697PCM711 module is used to perform operations related to storage, acquisition and communication applications.

Communication between the module and the PLC CPU is achieved via the backplane and does not require application support.

The IC697PCM711 module has multiple PCMs supported by a single IC697 PLC system and can accommodate up to 512 KB of optional expansion memory.

The IC697PCM711 module operates with an extended memory daughter board. It has a base memory with a maximum capacity of 95 KB of user memory.

The Expanded Memory Daughterboard can expand the data or programme memory to 64. 128. 512 or 2586 KB.

The IC697PCM711 module requires a 1-amp power supply, which is available from a 5-volt bus. When installed, the IC697PCM711 module should be referenced to the applicable programmable controller.

Be sure to disconnect rack power and install expansion memory where needed. In addition, it is necessary to connect the battery to either of the connectors provided with the unit.

The IC697PCM711 module can be operated without the expansion memory daughter board.

It can be programmed and configured simply by connecting an IC647 or IC640 computer or using an IBM compatible PC.

Description: The IC200MDD840 is a 32-point combination discrete I/O module in the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now part of Emerson Automation. The module has twenty (20) 24 VDC positive logic inputs and twelve (12) Type A 2.0 Amp rated relay contact outputs. The module has a maximum backplane current draw of 375 mA.

About the IC200MDD840

The IC200MDD840 is a component module in Emerson Automation’s VersaMax product family, formerly known as the General Electric Intelligent Platform (GE IP). The module is a combinational I/O module with embedded discrete input and output circuitry such as ten (10) positive logic 24 VDC inputs and twelve (12) A- or normally open (N.O.) contact outputs. The module has a maximum backplane current of 375 mA.

The input channels are divided into two (2) groups of ten (10) input channels each. Input characteristics include: input voltage compatibility from 0-30 VDC (24 VDC nominal); on-state voltages from +15 to +30 VDC; off-state voltages from 0 to 0.5 mA; typical on-state and off-state signal transition delays of up to 0.5 ms; and input impedance of up to 10k ohms. The input channels have configurable filtering times for both electrically and mechanically noisy input channels, eliminating false-positive and false-negative signals. These filter times include 0 ms, 1.0 ms, and 0.7 ms, with the default configuration being 1.0 ms.

The relay output channels are divided into two (2) groups dcs-sis.com of six (6) channels each. The contact outputs are rated at a minimum of 10mA per point; maximum current per module is 8.0A; 2.0 amps at 5 to 265VAC, maximum with resistive load; 2.0 amps at 5 to 30 VDC, maximum with resistive load; and 0.2 amps at 31 to 125 VDC, maximum with resistive load. Module relay types are fixed coil, moving armature, and silver alloy contact types.

About the IC200ALG432

The GE Fanuc IC200ALG432 module is a hybrid analogue module that uses a 10-volt DC power supply.

It is a 12-bit module with four channels and two output channels. The analogue module has an update rate of 0.4 ms and an input response time of 5 ms.

The analogue module requires an external power supply to power the outputs. The inputs of the module are powered by an external power supply for the transceiver.

The CPU in the module is responsible for processing the operation.The LEDs on the front of the IC200ALG432 module indicate the flow of power and backplane current.

There is no thermal derating with this hybrid module. the total current consumption of the IC200ALG432 module during normal operation is 160 milliamps, including load current.

The module’s diagnostic features help detect losses in the user-side power supply.

The GE Fanuc IC200ALG432 module comes with configurable alarms that can be set for different events.

During installation, the module should be protected from electromagnetic noise and airborne contaminants. The temperature of the installation area should not exceed 60 degrees Celsius.

The accuracy of the module depends on the ambient temperature. At 25 degrees Celsius, the accuracy is +/-0.3% of full scale; at 60 degrees Celsius, the accuracy is +/-0.3% of full scale.

At 60 degrees Celsius, the maximum accuracy is +/-1%. IC200ALG432 modules have a resolution of 8 counts.

The common mode voltage of the module is 0 V. The IC200ALG432 module has a bus current consumption of 60 mA when operating from a 5 V supply.

The GE Fanuc IC200PWR202 module is a power supply module with extended capabilities in the Versamax family.

It has an input voltage range of 9.5 to 15 volts DC, a nominal voltage of 12 volts DC, and output voltages of 5 volts DC and 3.3 volts DC.

About the IC200PWR202

The GE Fanuc Versamax IC200PWR202 power supply module features expanded functionality with up to 3-volt DC extended power supplies.

This module does not have an isolated power supply like other power modules in the Versamax family.

This device can power backpPLC channel devices including I/O modules, CPUs, and NIUs.

It can be used as a primary or secondary power supply in a system, especially when installed on a power booster carrier.

The GE Fanuc IC200PWR202 power supply module has an input voltage range of 9.6 to 15 volts DC and a nominal voltage of 12 volts DC.

Its output voltage is 5 volts DC or 3.3 volts DC. The module has a hold time of approximately 10 milliseconds and is rated at 11 watts of input power.

The GE Fanuc IC200PWR202 power supply module has an inrush current rating of 25 amps at 12 volts DC and 30 amps at 15 volts DC.

The total output current of the IC200PWR202 power supply module should not exceed 1.5 amps. When the output voltage is 3.3 volts DC, the output current is 1.0 amp.

When operating at 5 volts DC output current, the maximum output current is 1.5 amps minus 3.3 volts used.

The power supply module is designed with reverse polarity, short circuit, and overload protection.

The dimensions of the IC200PWR202 power supply module are 49 mm (1.93 in.) x 133.4 mm (5.25 in. x 39 mm (1.54 in.), not including DIN rail or carrier height.

Embedded Ethernet communication ports enable controller and media redundancy, thus increasing the availability of the I/O modules. These Ethernet ports feature a dedicated microprocessor core that allows the IC695CPE330 controller to simultaneously perform up to 48 SRTP server connections and 16 Modbus®/TCP server connections with up to 32 clients (SRTP or Modbux/SRTP) per connection.

In addition, the USB 2.0 master port allows uploading and downloading of programmes using ordinary USB flash drives and smartphones. This feature makes it easy to maintain the operation of the RX3i control system.

The IC695CPE330 supports programming languages such as Ladder Diagram (LD), Structured Text (ST), Function Block Diagram (FBD), or C. The IC695CPE330 also supports communication with third-party devices through OPC UA, an industry standard that can be implemented over Ethernet IP connections.

The IC695CPE330 CPU also supports a variety of IO protocols such as PROFINET, EGD, Modbus TCP, PROFIBUS, Genius, DeviceNet, Modbus RTU, and Reflected Memory (CMX) protocols. It is part of the RX3i family of CPUs with an embedded Ethernet/PROFINET interface.

The IC695CPE330 RX3i PacSystems CPU also supports the Rackmount PROFINET Controller Module for communications.The IC695ACC402 Energy Pack, IC695ACC412 Capacitor Pack, and the IC695CBL002 Connection Cable are some of the optional accessories for this module. The module panel has 6 LED status indicators, pushbuttons, and a 3-position run mode switch for easy monitoring and operation. The CPU must be mounted in the mainframe of an RX3i PLC system to integrate with any RX3i I/O module or Intelligent Option Module. Supporting up to 32K discrete and analogue I/O points, the IC695CPE330 RX3i CPU is the best choice for multi-layer communication and handling large amounts of data in complex industrial applications.

The IC695STK001 Starter Kit is the RX3i PacSystems Package 1 Starter Kit, part of GE Fanuc Automation’s RX3i PacSystems family.

Like the other starter kits, this kit is designed to meet the specific requirements of certain devices used in a PLC system. The kit includes a CPU and software.

The choice of CPU depends on the user and their application, and the different CPUs available include the IC695CPU310. IC695CHS012. IC695LRE001. IC695PSA040. IC695ETM001. IC694ACC300. IC694MDL940 and IC646MPP00 CPUs.

The GE Fanuc Automation IC695STK001 RX3i Package 1 Starter Kit is designed to provide a combination of hardware and software to install the CPU and make it ready for operation.

The CPUs in the GE Fanuc Automation IC695STK001 RX3i Package 1 Starter Kit provide real-time control of different devices in an application process.

These devices can be machines, processors, and material handling systems.

These CPUs share data with connected programmers and HIM devices that display the current status of the application process.

This particular CPU contains battery backed memory and non-volatile flash, configurable data and program memory.

Most 90-30 series modules and expansion racks are supported.