Month: June 2025

The IC695PNC001 is a PROFINET controller module. Formerly manufactured by GE Intelligent Platforms (GE IP), the module is now manufactured by Emerson Automation. This PROFINET controller enables the RX3i CPU to send and receive data over a PROFINET network.

The IC695PNC001 is compatible with PACSystem RX320i CPU7 or CPU0 with firmware version 3.315 or higher.The module comes with two (2) RJ-45 and two (2) SFP slots with SFP connectors sold separately. Only one IP address is assigned to these PROFINET ports. Up to four (4) IC695PNC001s may be installed on a single CPU and must be located only on the host rack where the CPU is located. Up to sixty-four (64) I/O devices can be connected to one (1) controller; 128 I/O devices per network, distributed among eight (8) I/O controllers. In addition, up to eight (8) I/O devices can be installed in a single network. The module has configurable data update times of 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms, and 512 ms IC695PNC001.

It occupies a single slot in the chassis and consumes 0.5 A without an SFP device installed and a maximum of 2.2 A with two (1) SFP devices installed, where the SFP device uses 0.35 A. At 5.5 VDC, the module consumes 1.5 A maximum.

In addition to the embedded dual PROFINET ports, the module is equipped with a micro USB connector for communicating with a computer using a command line interface. It must operate over a temperature range of 0-60 degrees Celsius.

The IC695BPM300 is a Profibus master module formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson.

It is now part of Emerson Automation’s PACSystems RX3i family of programmable automation controllers (PACs).

The module is used to exchange data over a Profibus network with a maximum of 3.584 bytes of input data and 3.584 bytes of output data.

This Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

This IC695BPM300 supports all standard data rates including 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s. The IC695BPM300 also supports the following data rates,

500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s, and 12 MBit/s. It can provide status information

It can provide status information such as slave status bit array list, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses.

It is mounted on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed on a PAC3i backplane with a host PAC3i running firmware revision 3.2 or later.

or later in a generic backplane of a host PACSystem RX9i controller. It consumes a backplane current of 440 mA @ 3.3 VDC.

The module is equipped with a Profibus OK ED indicator; a network indicator; and a MOD status indicator.

The module supports synchronization and freeze modes as well as Profibus DP-V1 read, write and alarm messages.

The IC695BPM300 comes with upgradable firmware that is received indirectly through the host controller via the WinLoader software utility.

The module must operate over a temperature range of 0 to 60 degrees Celsius and the module is stored at -40 to 85 degrees Celsius.

The IC695PBM300 PROFIBUS master module is manufactured by GE Intelligent Platforms/GE Fanuc in the RX3i PacSystems family.

The module is designed to enable the RX3i CPU to send or receive data over a PROFIBUS-DP network.

The IC695ALG808 is an Emerson Automation analog output module formerly manufactured by GE Intelligent Platforms (GE IP). The module features eight (8) independently isolated output channels that can be configured to provide 0-20 mA / 4-20 mA current signals and +/- 10 VDC / 0-10 VDC voltage signals.

The IC695ALG808 can be used to transmit output signals to modulating devices variable frequency drives (VFDs), control valves, dampers, shutters, and other devices. It can also be used to send signals to panel meters and data loggers that directly represent specific variables for local readout and recording.

This IC695ALG808 is compatible with a variety of terminal blocks such as cassette (IC694TBB032), expansion cassette (IC694TBB132), spring-loaded (IC694TBS032), or extended spring-loaded (IC694TBS132). The module requires an external 24 VDC to be terminated directly to the module terminals in order for the module to provide the required output signal.

All channels of the IC695ALG808 are configurable through software. Other parameters that can be configured include alarm settings such as very low, very low, very high, and very high alarms, module fault reporting, alarm latching, defining alarm limits, and setting upper and lower alarm limits. In addition, the module can set output biases to properly adjust the output to achieve the desired output for the process.

The IC20ALG4 has a 20-bit output resolution when configured to provide +/- 695 VDC, 808-15 mA, and 10-0 mA, and a 10-bit output resolution when configured for a 14-0 VDC output signal. In addition, it has an 8 ms analog update rate on all channels.

The IC695ALG728 is an analog output module that is part of the PACSystems RX3i family of midrange programmable automation controllers (PACs), manufactured by Emerson Automation and formerly known as the GE Intelligent Platform (GE IP). The module is capable of providing voltage and current signals and has the ability to be configured via the High Speed Addressable Remote Transducer (HART) protocol, as it supports HART version 5.0.

The IC695ALG728 features eight (8) non-isolated output channels that can be configured as +/-10 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA output signals with 14.9-bit voltage resolution, 0.20-bit at 15-9 mA, and 4.20-bit at 15-6 mA. The update time for each channel is 16 ms (HART communication) and 8 ms (without HART communication). The module’s output data format is configurable as a floating point IEEE 16-bit or 32-bit integer using 32-bit registers. The module is calibrated to 15.25% of full scale at 0°C and 30.60% of full scale when operating at 0°C. The output data format can be configured to use 32-bit registers with floating point IEEE 16-bit or 32-bit integers. In addition, the output build-up time is 2 ms for voltage configurations and 70 ms for HART and 23 ms without HART for current signals.

This IC695ALG728 requires an external power supply to operate. The appropriate power supply for this module must provide 19.2 – 30.0 VDC and 250 mA maximum supply current. The module mounts in any available slot in the RX3i chassis and can be located in either the local CPU chassis or the distributed I/O chassis. Other features of the module include clamping and alarm limits, alarm latching, and configurable output biasing.

The IC695ALG628 is an analog input module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was formerly manufactured by GE Intelligent Platforms (GE IP). The module features eight (8) non-isolated single-ended input channels or four (4) differential input channels supporting +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC, and 0-20 mA, 4-20 mA, and +/- 20mA input signals. The module has a built-in ADC converter that converts data to floating point data type integers with 24-bit resolution. The module supports High Speed Addressable Remote Sensor (HART) version 5.0.

About the IC695ALG628

The IC695ALG628 is an analog input module with High Speed Addressable Remote Sensor (HART) 5.0 functionality. This module is part of the mid-range controller family, the PACSystem Rx3i series with eight (8) analog input channels (configured as single-ended) and four (4) input channels (if used in a differential distribution line configuration). It comes with two (2) internal HART modems. The module’s parameters and configuration are completely software configurable and each channel can be individually assigned high alarm, low alarm, high high alarm, low low alarm detection and reporting to the CPU. In addition, positive and negative rate of change alarms and configurable interrupts for channel alarms and faults can be set accordingly. The module also comes with upgradable firmware and performs an automatic calibration each time the module is powered up.

The module’s analog input channels are designed to accept +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC and 0-20 mA, 4-20 mA and +/- 20mA input signals. It has built-in analog-to-digital (ADC) converter circuitry that converts received analog data to 24-bit registers or 32-bit integers in floating point. Each module channel has a variety of filter options, often used to eliminate signal fluctuations for more stable readings.

The IC695ALG608 is an analog input module for the PACsystem RX3i platform. When configured for single-ended wiring, the module is capable of providing up to eight (8) input channels and four (4) input channels for differential input wiring. It supports a variety of input signals such as +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC, and 0-20 mA, 4-20 mA, and +/- 20mA inputs, and has a built-in 24-bit analog-to-digital converter (ADC) that converts incoming analog data to integer or floating-point data.

The IC695ALG608 is mounted on the RX3i general-purpose backplane. It occupies a single slot in the rack and consumes 330 mA max @ 5.0V +5% / -2.5% and 600 mA max @ 3.3V +5% / -3%. This module is used with RX3i Central Processing Unit (CPU) firmware version 3.0 or higher and is configured using Machine Edition version 5.0 SP3 and higher. Available filter options for each input channel include 8Hz, 12Hz, 16Hz, 40Hz, 200Hz, and 500Hz, which are primarily used to normalize analog readings and eliminate fast fluctuations.

This IC695ALG608 is compatible with a variety of terminal blocks such as cassette (IC694TBB032), extended cassette (IC694TBB132), spring-loaded (IC694TBS032), or extended spring-loaded (IC694TBS132) terminal blocks. The module has no external jumpers for setting up module operation, but rather defines parameters via software-configurable parameters. In addition, the module features fully automatic calibration, on-board error checking, open-circuit detection, alarm setup, module fault reporting, channel alarm interrupts and faults, and other equally important features.

The GE Fanuc IC695ALG608 module is a non-isolated analog current or voltage input module that supports single-ended and differential distribution line configurations.